OpenRFC.org Requests For Comments ... for the community
Welcome to OpenRFC
Home Full RFC index RFC humour Our technology
 
RFC 4363
Definitions of Managed Objects for Bridges with Traffic Classes, Multicast Filtering, and Virtual LAN Extensions.
D. Levi, D. Harrington. January 2006.

 
[Direct link][Download PDF version][Download text version]
 

Network Working Group D. Levi Request for Comments: 4363 Nortel Networks Obsoletes: 2674 D. Harrington Category: Standards Track Effective Software January 2006 Definitions of Managed Objects for Bridges with Traffic Classes, Multicast Filtering, and Virtual LAN Extensions Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (C) The Internet Society (2006). Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in TCP/IP-based internets. In particular, it defines two MIB modules for managing the capabilities of MAC bridges defined by the IEEE 802.1D-1998 (TM) MAC Bridges and the IEEE 802.1Q-2003 (TM) Virtual LAN (VLAN) standards for bridging between Local Area Network (LAN) segments. One MIB module defines objects for managing the 'Traffic Classes' and 'Enhanced Multicast Filtering' components of IEEE 802.1D-1998 and P802.1t-2001 (TM). The other MIB module defines objects for managing VLANs, as specified in IEEE 802.1Q-2003, P802.1u (TM), and P802.1v (TM). Provisions are made for support of transparent bridging. Provisions are also made so that these objects apply to bridges connected by subnetworks other than LAN segments. This memo supplements RFC 4188 and obsoletes RFC 2674. Levi & Harrington Standards Track [Page 1]
RFC 4363 Bridge MIB Extensions January 2006 Table of Contents 1. The Internet-Standard Management Framework ......................3 2. Overview ........................................................3 2.1. Scope ......................................................3 3. Structure of MIBs ...............................................4 3.1. Structure of Extended Bridge MIB Module ....................5 3.1.1. Relationship to IEEE 802.1D-1998 Manageable Objects .............................................5 3.1.2. Relationship to IEEE 802.1Q Manageable Objects ......6 3.1.3. The dot1dExtBase Subtree ............................7 3.1.4. The dot1dPriority Subtree ...........................7 3.1.5. The dot1dGarp Subtree ...............................7 3.1.6. The dot1dGmrp Subtree ...............................7 3.1.7. The dot1dTpHCPortTable ..............................8 3.1.8. The dot1dTpPortOverflowTable ........................8 3.2. Structure of Virtual Bridge MIB module .....................8 3.2.1. Relationship to IEEE 802.1Q Manageable Objects ......8 3.2.2. The dot1qBase Subtree ..............................12 3.2.3. The dot1qTp Subtree ................................12 3.2.4. The dot1qStatic Subtree ............................12 3.2.5. The dot1qVlan Subtree ..............................12 3.3. Textual Conventions .......................................12 3.4. Relationship to Other MIBs ................................13 3.4.1. Relationship to the SNMPv2-MIB .....................13 3.4.2. Relationship to the IF-MIB .........................13 3.4.2.1. Layering Model ............................14 3.4.2.2. ifStackTable ..............................15 3.4.2.3. ifRcvAddressTable .........................15 3.4.3. Relationship to the BRIDGE-MIB .....................16 3.4.3.1. The dot1dBase Subtree .....................16 3.4.3.2. The dot1dStp Subtree ......................16 3.4.3.3. The dot1dTp Subtree .......................16 3.4.3.4. The dot1dStatic Subtree ...................17 3.4.3.5. Additions to the BRIDGE-MIB ...............17 4. Definitions for Extended Bridge MIB ............................18 5. Definitions for Virtual Bridge MIB .............................42 6. Acknowledgements ...............................................91 7. Security Considerations ........................................91 8. Normative References ...........................................94 9. Informative References .........................................95 Appendix A. Email from Tony Jeffrey from IEEE .....................96 Levi & Harrington Standards Track [Page 2]
RFC 4363 Bridge MIB Extensions January 2006 1. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 2. Overview A common device present in many networks is the Bridge. This device is used to connect Local Area Network segments below the network layer. These devices are often known as 'layer 2 switches'. The transparent method of bridging is defined by IEEE 802.1D-1998 [802.1D]. Managed objects for transparent bridging are defined in the BRIDGE-MIB [BRIDGE-MIB]. The original IEEE 802.1D is augmented by IEEE 802.1Q-2003 [802.1Q] to provide support for 'virtual bridged LANs' where a single bridged physical LAN network may be used to support multiple logical bridged LANs, each of which offers a service approximately the same as that defined by IEEE 802.1D. Such virtual LANs (VLANs) are an integral feature of switched LAN networks. A VLAN can be viewed as a group of end-stations on multiple LAN segments and can communicate as if they were on a single LAN. IEEE 802.1Q defines port-based Virtual LANs where membership is determined by the bridge port on which data frames are received, and port-and-protocol-based Virtual LANs where membership is determined by the bridge port on which frames are received and the protocol identifier of the frame. This memo defines the objects needed for the management of port-based VLANs in bridge entities. This memo supplements RFC 4188 [BRIDGE-MIB] and obsoletes RFC 2674 [RFC2674]. 2.1. Scope The MIB modules defined in this document include a comprehensive set of managed objects that attempts to match the set defined in IEEE 802.1D and IEEE 802.1Q. However, to be consistent with the spirit of Levi & Harrington Standards Track [Page 3]
RFC 4363 Bridge MIB Extensions January 2006 the SNMP Framework, a subjective judgement was made to omit the objects from those standards most 'costly' to implement in an agent and least 'essential' for fault and configuration management. The omissions are described in Section 3 below. Historical note: The original BRIDGE-MIB [RFC1493] used the following principles for determining inclusion of an object in the BRIDGE-MIB module: (1) Start with a small set of essential objects and add only as further objects are needed. (2) Require that objects be essential for either fault or configuration management. (3) Consider evidence of current use and/or utility. (4) Limit the total number of objects. (5) Exclude objects that are simply derivable from others in this or other MIBs. (6) Avoid causing critical sections to be heavily instrumented. The guideline that was followed is one counter per critical section per layer. 3. Structure of MIBs This document defines objects that supplement those in the BRIDGE-MIB module [BRIDGE-MIB]. Section 3.4.3 of the present document contains some recommendations regarding usage of objects in the BRIDGE-MIB by devices implementing the enhancements defined here. An extended bridge MIB module P-BRIDGE-MIB defines managed objects for the traffic class and multicast filtering enhancements defined by IEEE 802.1D-1998 [802.1D], including the Restricted Group Registration control defined by IEEE P802.1t [802.1t]. A virtual bridge MIB module Q-BRIDGE-MIB defines managed objects for the Virtual LAN bridging enhancements defined by IEEE 802.1Q-2003 [802.1Q], including the Restricted VLAN Registration control, defined by IEEE P802.1u [802.1u], and the VLAN Classification by Protocol and Port enhancement, defined by IEEE P802.1v [802.1v]. Levi & Harrington Standards Track [Page 4]
RFC 4363 Bridge MIB Extensions January 2006 3.1. Structure of Extended Bridge MIB Module Objects in this MIB are arranged into subtrees. Each subtree is organized as a set of related objects. The overall structure and assignment of objects to their subtrees is shown below. 3.1.1. Relationship to IEEE 802.1D-1998 Manageable Objects This section contains a cross-reference to the objects defined in IEEE 802.1D-1998 [802.1D]. It also details those objects that are not considered necessary in this MIB module. Some objects defined by IEEE 802.1D-1998 have been included in the virtual bridge MIB module rather than this one: entries in dot1qTpGroupTable, dot1qForwardAllTable, and dot1qForwardUnregisteredTable are required for virtual bridged LANs with additional indexing (e.g., per-VLAN, per-Filtering-Database (per-FDB)) and so are not defined here. Instead, devices that do not implement virtual bridged LANs but do implement the Extended Forwarding Services defined by IEEE 802.1D (i.e., dynamic learning of multicast group addresses and group service requirements in the filtering database) should implement these tables with a fixed value for dot1qFdbId (the value 1 is recommended) or dot1qVlanIndex (the value 1 is recommended). Devices that support Extended Filtering Services should support dot1qTpGroupTable, dot1qForwardAllTable, and dot1qForwardUnregisteredTable. Extended Bridge MIB Name IEEE 802.1D-1998 Name dot1dExtBase Bridge dot1dDeviceCapabilities dot1dExtendedFilteringServices dot1dTrafficClasses dot1dTrafficClassesEnabled dot1dGmrpStatus .ApplicantAdministrativeControl dot1dPriority dot1dPortPriorityTable dot1dPortDefaultUserPriority .UserPriority dot1dPortNumTrafficClasses dot1dUserPriorityRegenTable .UserPriorityRegenerationTable dot1dUserPriority dot1dRegenUserPriority dot1dTrafficClassTable .TrafficClassTable dot1dTrafficClassPriority dot1dTrafficClass dot1dPortOutboundAccessPriorityTable .OutboundAccessPriorityTable dot1dPortOutboundAccessPriority Levi & Harrington Standards Track [Page 5]
RFC 4363 Bridge MIB Extensions January 2006 dot1dGarp dot1dPortGarpTable dot1dPortGarpJoinTime .JoinTime dot1dPortGarpLeaveTime .LeaveTime dot1dPortGarpLeaveAllTime .LeaveAllTime dot1dGmrp dot1dPortGmrpTable dot1dPortGmrpStatus .ApplicantAdministrativeControl dot1dPortGmrpFailedRegistrations .FailedRegistrations dot1dPortGmrpLastPduOrigin .OriginatorOfLastPDU dot1dPortRestrictedGroupRegistration Restricted Group Registration (Ref. IEEE 802.1t 10.3.2.3) dot1dTp dot1dTpHCPortTable dot1dTpHCPortInFrames .BridgePort.FramesReceived dot1dTpHCPortOutFrames .ForwardOutBound dot1dTpHCPortInDiscards .DiscardInbound dot1dTpPortOverflowTable dot1dTpPortInOverflowFrames .BridgePort.FramesReceived dot1dTpPortOutOverflowFrames .ForwardOutBound dot1dTpPortInOverflowDiscards .DiscardInbound The following IEEE 802.1D-1998 management objects have not been included in the Bridge MIB for the indicated reasons. IEEE 802.1D-1998 Object Disposition Bridge.StateValue not considered useful Bridge.ApplicantAdministrativeControl not provided per-attribute (e.g., per-VLAN, per-Group). Only per-{device,port,application} control is provided in this MIB. notify group registration failure not considered useful (IEEE 802.1t 14.10.1.2) 3.1.2. Relationship to IEEE 802.1Q Manageable Objects This section contains section number cross-references to manageable objects defined in IEEE 802.1Q-2003 [802.1Q]. These objects have been included in this MIB as they provide a natural fit with the IEEE 802.1D objects with which they are co-located. Levi & Harrington Standards Track [Page 6]
RFC 4363 Bridge MIB Extensions January 2006 Extended Bridge MIB Name IEEE 802.1Q-2003 Section and Name dot1dExtBase Bridge dot1dDeviceCapabilities dot1qStaticEntryIndividualPort 5.2 implementation options dot1qIVLCapable dot1qSVLCapable dot1qHybridCapable dot1qConfigurablePvidTagging 12.10.1.1 read bridge vlan config dot1dLocalVlanCapable dot1dPortCapabilitiesTable dot1dPortCapabilities dot1qDot1qTagging 5.2 implementation options dot1qConfigurableAcceptableFrameTypes 5.2 implementation options dot1qIngressFiltering 5.2 implementation options 3.1.3. The dot1dExtBase Subtree This subtree contains the objects that are applicable to all bridges implementing the traffic class and multicast filtering features of IEEE 802.1D-1998 [802.1D]. It includes per-device configuration of Generic Attribute Registration Protocol (GARP) and GARP Multicast Registration Protocol (GMRP) protocols. 3.1.4. The dot1dPriority Subtree This subtree contains the objects for configuring and reporting status of priority-based queuing mechanisms in a bridge. This includes per-port user_priority treatment, mapping of user_priority in frames into internal traffic classes, and outbound user_priority and access_priority. 3.1.5. The dot1dGarp Subtree This subtree contains the objects for configuring and reporting on operation of the Generic Attribute Registration Protocol (GARP). 3.1.6. The dot1dGmrp Subtree This subtree contains the objects for configuring and reporting on operation of the GARP Multicast Registration Protocol (GMRP). Levi & Harrington Standards Track [Page 7]
RFC 4363 Bridge MIB Extensions January 2006 3.1.7. The dot1dTpHCPortTable This table extends the dot1dTp subtree from the BRIDGE-MIB [BRIDGE-MIB] and contains the objects for reporting port-bridging statistics for high-capacity network interfaces. 3.1.8. The dot1dTpPortOverflowTable This table extends the dot1dTp subtree from the BRIDGE-MIB [BRIDGE-MIB] and contains the objects for reporting the upper bits of port-bridging statistics for high-capacity network interfaces for when 32-bit counters are inadequate. 3.2. Structure of Virtual Bridge MIB module Objects in this MIB are arranged into subtrees. Each subtree is organized as a set of related objects. The overall structure and assignment of objects to their subtrees is shown below. Some manageable objects defined in the BRIDGE-MIB [BRIDGE-MIB] need to be indexed differently when they are used in a VLAN bridging environment: these objects are, therefore, effectively duplicated by new objects with different indexing, which are defined in the Virtual Bridge MIB. 3.2.1. Relationship to IEEE 802.1Q Manageable Objects This section contains section-number cross-references to manageable objects defined in clause 12 of IEEE 802.1Q-2003 [802.1Q]. It also details those objects that are not considered necessary in this MIB module. Note: Unlike IEEE 802.1D-1998, IEEE 802.1Q-2003 [802.1Q] did not define exact syntax for a set of managed objects. The following cross-references indicate the section numbering of the descriptions of management operations from clause 12 in the latter document. Virtual Bridge MIB object IEEE 802.1Q-2003 Reference dot1qBase dot1qVlanVersionNumber 12.10.1.1 read bridge vlan config dot1qMaxVlanId 12.10.1.1 read bridge vlan config dot1qMaxSupportedVlans 12.10.1.1 read bridge vlan config dot1qNumVlans dot1qGvrpStatus 12.9.2.1/2 read/set garp applicant controls dot1qTp dot1qFdbTable dot1qFdbId Levi & Harrington Standards Track [Page 8]
RFC 4363 Bridge MIB Extensions January 2006 dot1qFdbDynamicCount 12.7.1.1.3 read filtering d/base dot1qTpFdbTable dot1qTpFdbAddress dot1qTpFdbPort dot1qTpFdbStatus dot1qTpGroupTable 12.7.7.1 read filtering entry dot1qTpGroupAddress dot1qTpGroupEgressPorts dot1qTpGroupLearnt dot1qForwardAllTable 12.7.7.1 read filtering entry dot1qForwardAllPorts dot1qForwardAllStaticPorts dot1qForwardAllForbiddenPorts dot1qForwardUnregisteredTable 12.7.7.1 read filtering entry dot1qForwardUnregisteredPorts dot1qForwardUnregisteredStaticPorts dot1qForwardUnregisteredForbiddenPorts dot1qStatic dot1qStaticUnicastTable 12.7.7.1 create/delete/read filtering entry 12.7.6.1 read permanent database dot1qStaticUnicastAddress dot1qStaticUnicastReceivePort dot1qStaticUnicastAllowedToGoTo dot1qStaticUnicastStatus dot1qStaticMulticastTable 12.7.7.1 create/delete/read filtering entry 12.7.6.1 read permanent database dot1qStaticMulticastAddress dot1qStaticMulticastReceivePort dot1qStaticMulticastStaticEgressPorts dot1qStaticMulticastForbiddenEgressPorts dot1qStaticMulticastStatus dot1qVlan dot1qVlanNumDeletes dot1qVlanCurrentTable 12.10.2.1 read vlan configuration 12.10.3.5 read VID to FID allocations 12.10.3.6 read FID allocated to VID 12.10.3.7 read VIDs allocated to FID dot1qVlanTimeMark dot1qVlanIndex dot1qVlanFdbId dot1qVlanCurrentEgressPorts dot1qVlanCurrentUntaggedPorts dot1qVlanStatus Levi & Harrington Standards Track [Page 9]
RFC 4363 Bridge MIB Extensions January 2006 dot1qVlanCreationTime dot1qVlanStaticTable 12.7.7.1/2/3 create/delete/read filtering entry 12.7.6.1 read permanent database 12.10.2.2 create vlan config 12.10.2.3 delete vlan config dot1qVlanStaticName 12.4.1.3 set bridge name dot1qVlanStaticEgressPorts dot1qVlanForbiddenEgressPorts dot1qVlanStaticUntaggedPorts dot1qVlanStaticRowStatus dot1qNextFreeLocalVlanIndex dot1qPortVlanTable 12.10.1.1 read bridge vlan configuration dot1qPvid 12.10.1.2 configure PVID values dot1qPortAcceptableFrameTypes 12.10.1.3 configure acceptable frame types parameter dot1qPortIngressFiltering 12.10.1.4 configure ingress filtering parameters dot1qPortGvrpStatus 12.9.2.2 read/set garp applicant controls dot1qPortGvrpFailedRegistrations dot1qPortGvrpLastPduOrigin dot1qPortRestrictedVlanRegistration IEEE 802.1u 11.2.3.2.3 Restricted VLAN Registration dot1qPortVlanStatisticsTable 12.6.1.1 read forwarding port counters dot1qTpVlanPortInFrames dot1qTpVlanPortOutFrames dot1qTpVlanPortInDiscards dot1qTpVlanPortInOverflowFrames dot1qTpVlanPortOutOverflowFrames dot1qTpVlanPortInOverflowDiscards dot1qPortVlanHCStatisticsTable 12.6.1.1 read forwarding port counters dot1qTpVlanPortHCInFrames dot1qTpVlanPortHCOutFrames dot1qTpVlanPortHCInDiscards dot1qLearningConstraintsTable 12.10.3.1/3/4 read/set/delete vlan learning constraints 12.10.3.2 read vlan learning constraints for VID dot1qConstraintVlan dot1qConstraintSet dot1qConstraintType dot1qConstraintStatus dot1qConstraintSetDefault Levi & Harrington Standards Track [Page 10]
RFC 4363 Bridge MIB Extensions January 2006 dot1qConstraintTypeDefault dot1vProtocol IEEE 802.1v Reference: dot1vProtocolGroupTable 8.6.4 Protocol Group Database, 8.6.2 Protocol Template dot1vProtocolTemplateFrameType dot1vProtocolTemplateProtocolValue dot1vProtocolGroupId 8.6.3 Protocol Group Identifier dot1vProtocolGroupRowStatus dot1vProtocolPortTable 8.4.4 VID Set for each Port dot1vProtocolPortGroupId dot1vProtocolGroupVid dot1vProtocolPortRowStatus The following IEEE 802.1Q management objects have not been included in the Bridge MIB for the indicated reasons. IEEE 802.1Q-2003 Operation Disposition reset bridge (12.4.1.4) not considered useful reset vlan bridge (12.10.1.5) not considered useful read forwarding port counters (12.6.1.1) discard on error details not considered useful read permanent database (12.7.6.1) permanent database size not considered useful number of static filtering count rows in entries dot1qStaticUnicastTable + dot1qStaticMulticastTable number of static VLAN count rows in registration entries dot1qVlanStaticTable read filtering entry range use GetNext operation. (12.7.7.4) read filtering database (12.7.1.1) filtering database size not considered useful number of dynamic group address count rows applicable to each entries (12.7.1.3) FDB in dot1dTpGroupTable read garp state (12.9.3.1) not considered useful notify vlan registration failure not considered useful (12.10.1.6) Levi & Harrington Standards Track [Page 11]
RFC 4363 Bridge MIB Extensions January 2006 notify learning constraint violation (12.10.3.10) not considered useful 3.2.2. The dot1qBase Subtree This subtree contains the objects that are applicable to all bridges implementing IEEE 802.1Q virtual LANs. 3.2.3. The dot1qTp Subtree This subtree contains objects that control the operation and report the status of transparent bridging. This includes management of the dynamic Filtering Databases for both unicast and multicast forwarding. This subtree will be implemented by all bridges that perform destination-address filtering. 3.2.4. The dot1qStatic Subtree This subtree contains objects that control static configuration information for transparent bridging. This includes management of the static entries in the Filtering Databases for both unicast and multicast forwarding. 3.2.5. The dot1qVlan Subtree This subtree contains objects that control configuration and report status of the Virtual LANs known to a bridge. This includes management of the statically configured VLANs as well as reporting VLANs discovered by other means (e.g., GARP VLAN Registration Protocol (GVRP)). It also controls configuration and reports status of per-port objects relating to VLANs and reports traffic statistics. It also provides for management of the VLAN Learning Constraints. 3.3. Textual Conventions Various Working Groups have defined standards-track MIB documents (for example, [RFC2613] and [RFC3318]), that contain objects and Textual Conventions to represent a Virtual Local Area Network Identifier (VLAN-ID) [802.1Q]. New definitions are showing up in various documents (for example, [RFC4323] and [RFC4149]). Unfortunately, the result is a set of different definitions for the same piece of management information. This may lead to confusion and unnecessary complexity. In order to address this situation, three new textual conventions are defined in the Q-BRIDGE-MIB, called VlanIdOrAny, VlanIdOrNone, and VlanIdOrAnyOrNone. These new textual conventions should be (re)used in MIB modules so that they all represent a VLAN-ID in the same way. Levi & Harrington Standards Track [Page 12]
RFC 4363 Bridge MIB Extensions January 2006 These textual conventions provide a means to specify MIB objects that refer to a specific VLAN, to any VLAN, or to no VLAN. For an example of how these textual conventions might be used, consider a MIB object, with SYNTAX of VlanIdOrAnyOrNone, that specifies the VLAN on which to accept incoming packets of a particular protocol. Such an object would allow the device to be configured to accept packets of this protocol received with a specific 802.1q tag value, with any 802.1q tag value, or with no 802.1q tag. Note that a MIB object that is defined using one of these textual conventions should clarify the meaning of 'any VLAN' and/or 'no VLAN' in its DESCRIPTION clause. 3.4. Relationship to Other MIBs As described above, some IEEE 802.1D management objects have not been included in this MIB because they overlap with objects in other MIBs applicable to a bridge implementing this MIB module. 3.4.1. Relationship to the SNMPv2-MIB The SNMPv2-MIB [RFC3418] defines objects that are generally applicable to managed devices. These objects apply to the device as a whole, irrespective of whether bridging is the device's sole functionality or only a subset of the device's functionality. Full support for the 802.1D management objects requires that the SNMPv2-MIB objects sysDescr and sysUpTime be implemented. Note that compliance to the current SNMPv2-MIB module requires additional objects and notifications to be implemented as specified in RFC 3418 [RFC3418]. 3.4.2. Relationship to the IF-MIB The IF-MIB, [RFC2863], requires that any MIB that is an adjunct of the IF-MIB clarify specific areas within the IF-MIB. These areas were intentionally left vague in the IF-MIB in order to avoid over- constraining the MIB, thereby precluding management of certain media-types. The IF-MIB enumerates several areas that a media-specific MIB must clarify. Each of these areas is addressed in a following subsection. The implementor is referred to the IF-MIB in order to understand the general intent of these areas. The IF-MIB [RFC2863] defines managed objects for managing network interfaces. A network interface is considered attached to a 'subnetwork'. (Note that this term is not to be confused with 'subnet', which refers to an addressing partitioning scheme used in the Internet suite of protocols.) The term 'segment' is used in this Levi & Harrington Standards Track [Page 13]
RFC 4363 Bridge MIB Extensions January 2006 memo to refer to such a subnetwork, whether it be an Ethernet segment, a 'ring', a WAN link, or even an X.25 virtual circuit. Full support for the 802.1D management objects requires that the IF-MIB objects ifIndex, ifType, ifDescr, ifPhysAddress, and ifLastChange are implemented. Note that compliance to the current IF-MIB module requires additional objects and notifications to be implemented as specified in RFC 2863 [RFC2863]. Implicit in this Extended Bridge MIB is the notion of ports on a bridge. Each of these ports is associated with one interface of the 'interfaces' subtree (one row in ifTable), and, in most situations, each port is associated with a different interface. However, there are situations in which multiple ports are associated with the same interface. An example of such a situation would be several ports each corresponding one-to-one with several X.25 virtual circuits but all on the same interface. Each port is uniquely identified by a port number. A port number has no mandatory relationship to an interface number, but in the simple case a port number will have the same value as the corresponding interface's interface number. Port numbers are in the range (1..dot1dBaseNumPorts). Some entities perform other functionality as well as bridging through the sending and receiving of data on their interfaces. In such situations, only a subset of the data sent/received on an interface is within the domain of the entity's bridging functionality. This subset is considered delineated according to a set of protocols, with some protocols being bridged, and other protocols not being bridged. For example, in an entity that exclusively performed bridging, all protocols would be considered bridged, whereas in an entity that performed IP routing on IP datagrams and only bridged other protocols, only the non-IP data would be considered bridged. Thus, this Extended Bridge MIB (and in particular, its counters) is applicable only to that subset of the data on an entity's interfaces that is sent/received for a protocol being bridged. All such data is sent/received via the ports of the bridge. 3.4.2.1. Layering Model This memo assumes the interpretation of the Interfaces Subtree to be in accordance with the IF-MIB [RFC2863], which states that the interfaces table (ifTable) contains information on the managed resource's interfaces and that each sub-layer below the internetwork layer of a network interface is considered an interface. Levi & Harrington Standards Track [Page 14]
RFC 4363 Bridge MIB Extensions January 2006 This document does not make any assumption that within an entity, VLANs that are instantiated as an entry in dot1qVlanCurrentTable by either management configuration through dot1qVlanStaticTable or by dynamic means (e.g., through GVRP) are also represented by an entry in ifTable. Where an entity contains higher-layer protocol entities (e.g., IP-layer interfaces that transmit and receive traffic to/from a VLAN), these should be represented in the ifTable as interfaces of type propVirtual(53). Protocol-specific types such as l3ipxvlan(137) should not be used here, since there is no implication that the bridge will perform any protocol filtering before delivering up to these virtual interfaces. 3.4.2.2. ifStackTable In addition, the IF-MIB [RFC2863] defines a table 'ifStackTable' for describing the relationship between logical interfaces within an entity. It is anticipated that implementors will use this table to describe the binding of (for example) IP interfaces to physical ports, although the presence of VLANs makes the representation less than perfect for showing connectivity. The ifStackTable cannot represent the full capability of the IEEE 802.1Q VLAN bridging standard, since that makes a distinction between VLAN bindings on 'ingress' to and 'egress' from a port: these relationships may or may not be symmetrical whereas Interface MIB Evolution assumes a symmetrical binding for transmit and receive. This makes it necessary to define other manageable objects for configuring which ports are members of which VLANs. 3.4.2.3. ifRcvAddressTable This table contains all MAC addresses, unicast, multicast, and broadcast, for which an interface will receive packets and forward them up to a higher-layer entity for local consumption. Note that this does not include addresses for data-link layer control protocols such as Spanning-Tree, GMRP, or GVRP. The format of the address, contained in ifRcvAddressAddress, is the same as for ifPhysAddress. This table does not include unicast or multicast addresses that are accepted for possible forwarding out some other port. This table is explicitly not intended to provide a bridge address filtering mechanism. Levi & Harrington Standards Track [Page 15]
RFC 4363 Bridge MIB Extensions January 2006 3.4.3. Relationship to the BRIDGE-MIB This section defines how objects in the BRIDGE-MIB module [BRIDGE-MIB] should be represented for devices that implement the extensions: some of the old objects are less useful in such devices but must still be implemented for reasons of backwards compatibility. 3.4.3.1. The dot1dBase Subtree This subtree contains objects that are applicable to all types of bridges. Interpretation of this subtree is unchanged. 3.4.3.2. The dot1dStp Subtree This subtree contains the objects that denote the bridge's state with respect to the Spanning Tree Protocol. Interpretation of this subtree is unchanged. 3.4.3.3. The dot1dTp Subtree This subtree contains objects that describe the entity's state with respect to transparent bridging. In a device operating with a single Filtering Database, interpretation of this subtree is unchanged. In a device supporting multiple Filtering Databases, this subtree is interpreted as follows: dot1dTpLearnedEntryDiscards The number of times that *any* of the FDBs became full. dot1dTpAgingTime This applies to all Filtering Databases. dot1dTpFdbTable Report MAC addresses learned on each port, regardless of which Filtering Database they have been learned in. If an address has been learned in multiple databases on a single port, report it only once. If an address has been learned in multiple databases on more than one port, report the entry on any one of the valid ports. Levi & Harrington Standards Track [Page 16]
RFC 4363 Bridge MIB Extensions January 2006 dot1dTpPortTable This table is port-based and is not affected by multiple Filtering Databases or multiple VLANs. The counters should include frames received or transmitted for all VLANs. Note that equivalent 64-bit port statistics counters, as well as other objects to represent the upper 32 bits of these counters, are defined in this document for high-capacity network interfaces. These have conformance statements to indicate for which speeds of interface they are required. 3.4.3.4. The dot1dStatic Subtree This optional subtree contains objects that describe the configuration of destination-address filtering. In a device operating with a single Filtering Database, interpretation of this subtree is unchanged. In a device supporting multiple Filtering Databases, this subtree is interpreted as follows: dot1dStaticTable Entries read from this table include all static entries from all of the Filtering Databases. Entries for the same MAC address and receive port in more than one Filtering Database must appear only once, since these are the indices of this table. This table should be implemented as read-only in devices that support multiple Forwarding Databases. Instead, write access should be provided through dot1qStaticUnicastTable and dot1qStaticMulticastTable, as defined in this document. 3.4.3.5. Additions to the BRIDGE-MIB To supplement the BRIDGE-MIB [BRIDGE-MIB], this module contains: (1) support for multiple traffic classes and dynamic multicast filtering as per IEEE 802.1D-1998 [802.1D]. (2) support for bridged Virtual LANs as per IEEE 802.1Q-2003 [802.1Q]. (3) support for 64-bit versions of BRIDGE-MIB [BRIDGE-MIB] port counters. Levi & Harrington Standards Track [Page 17]
RFC 4363 Bridge MIB Extensions January 2006 4. Definitions for Extended Bridge MIB P-BRIDGE-MIB DEFINITIONS ::= BEGIN -- ------------------------------------------------------------- -- MIB for IEEE 802.1p devices -- ------------------------------------------------------------- IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, Counter64 FROM SNMPv2-SMI TruthValue, TimeInterval, MacAddress, TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF dot1dTp, dot1dTpPort, dot1dBridge, dot1dBasePortEntry, dot1dBasePort FROM BRIDGE-MIB; pBridgeMIB MODULE-IDENTITY LAST-UPDATED "200601090000Z" ORGANIZATION "IETF Bridge MIB Working Group" CONTACT-INFO "Email: bridge-mib@ietf.org ietfmibs@ops.ietf.org David Levi Postal: Nortel Networks 4655 Great America Parkway Santa Clara, CA 95054 USA Phone: +1 865 686 0432 Email: dlevi@nortel.com David Harrington Postal: Effective Software 50 Harding Rd. Portsmouth, NH 03801 USA Phone: +1 603 436 8634 Email: ietfdbh@comcast.net Les Bell Postal: Hemel Hempstead, Herts. HP2 7YU UK Email: elbell@ntlworld.com Vivian Ngai Levi & Harrington Standards Track [Page 18]
RFC 4363 Bridge MIB Extensions January 2006 Email: vivian_ngai@acm.org Andrew Smith Postal: Beijing Harbour Networks Jiuling Building 21 North Xisanhuan Ave. Beijing, 100089 PRC Fax: +1 415 345 1827 Email: ah_smith@acm.org Paul Langille Postal: Newbridge Networks 5 Corporate Drive Andover, MA 01810 USA Phone: +1 978 691 4665 Email: langille@newbridge.com Anil Rijhsinghani Postal: Accton Technology Corporation 5 Mount Royal Ave Marlboro, MA 01752 USA Phone: Email: anil@accton.com Keith McCloghrie Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Phone: +1 408 526 5260 Email: kzm@cisco.com" DESCRIPTION "The Bridge MIB Extension module for managing Priority and Multicast Filtering, defined by IEEE 802.1D-1998, including Restricted Group Registration defined by IEEE 802.1t-2001. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4363; See the RFC itself for full legal notices." REVISION "200601090000Z" DESCRIPTION "Added dot1dPortRestrictedGroupRegistration. Deprecated pBridgePortGmrpGroup and pBridgeCompliance and added pBridgePortGmrpGroup2 and pBridgeCompliance2." Levi & Harrington Standards Track [Page 19]
RFC 4363 Bridge MIB Extensions January 2006 REVISION "199908250000Z" DESCRIPTION "The Bridge MIB Extension module for managing Priority and Multicast Filtering, defined by IEEE 802.1D-1998. Initial version, published as RFC 2674." ::= { dot1dBridge 6 } pBridgeMIBObjects OBJECT IDENTIFIER ::= { pBridgeMIB 1 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- EnabledStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A simple status value for the object." SYNTAX INTEGER { enabled(1), disabled(2) } -- ------------------------------------------------------------- -- subtrees in the P-BRIDGE MIB -- ------------------------------------------------------------- dot1dExtBase OBJECT IDENTIFIER ::= { pBridgeMIBObjects 1 } dot1dPriority OBJECT IDENTIFIER ::= { pBridgeMIBObjects 2 } dot1dGarp OBJECT IDENTIFIER ::= { pBridgeMIBObjects 3 } dot1dGmrp OBJECT IDENTIFIER ::= { pBridgeMIBObjects 4 } -- ------------------------------------------------------------- -- the dot1dExtBase subtree -- ------------------------------------------------------------- dot1dDeviceCapabilities OBJECT-TYPE SYNTAX BITS { dot1dExtendedFilteringServices(0), dot1dTrafficClasses(1), dot1qStaticEntryIndividualPort(2), dot1qIVLCapable(3), dot1qSVLCapable(4), dot1qHybridCapable(5), dot1qConfigurablePvidTagging(6), dot1dLocalVlanCapable(7) } MAX-ACCESS read-only STATUS current DESCRIPTION Levi & Harrington Standards Track [Page 20]
RFC 4363 Bridge MIB Extensions January 2006 "Indicates the optional parts of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities. dot1dExtendedFilteringServices(0), -- can perform filtering of -- individual multicast addresses -- controlled by GMRP. dot1dTrafficClasses(1), -- can map user priority to -- multiple traffic classes. dot1qStaticEntryIndividualPort(2), -- dot1qStaticUnicastReceivePort & -- dot1qStaticMulticastReceivePort -- can represent non-zero entries. dot1qIVLCapable(3), -- Independent VLAN Learning (IVL). dot1qSVLCapable(4), -- Shared VLAN Learning (SVL). dot1qHybridCapable(5), -- both IVL & SVL simultaneously. dot1qConfigurablePvidTagging(6), -- whether the implementation -- supports the ability to -- override the default PVID -- setting and its egress status -- (VLAN-Tagged or Untagged) on -- each port. dot1dLocalVlanCapable(7) -- can support multiple local -- bridges, outside of the scope -- of 802.1Q defined VLANs." REFERENCE "ISO/IEC 15802-3 Section 5.2, IEEE 802.1Q/D11 Section 5.2, 12.10.1.1.3/b/2" ::= { dot1dExtBase 1 } dot1dTrafficClassesEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The value true(1) indicates that Traffic Classes are enabled on this bridge. When false(2), the bridge operates with a single priority level for all traffic. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { true } Levi & Harrington Standards Track [Page 21]
RFC 4363 Bridge MIB Extensions January 2006 ::= { dot1dExtBase 2 } dot1dGmrpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status requested by management for GMRP. The value enabled(1) indicates that GMRP should be enabled on this device, in all VLANs, on all ports for which it has not been specifically disabled. When disabled(2), GMRP is disabled, in all VLANs and on all ports, and all GMRP packets will be forwarded transparently. This object affects both Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GMRP state machines on all ports. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { enabled } ::= { dot1dExtBase 3 } -- ------------------------------------------------------------- -- Port Capabilities Table -- ------------------------------------------------------------- dot1dPortCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains capabilities information about every port that is associated with this bridge." ::= { dot1dExtBase 4 } dot1dPortCapabilitiesEntry OBJECT-TYPE SYNTAX Dot1dPortCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of capabilities information about this port indexed by dot1dBasePort." AUGMENTS { dot1dBasePortEntry } ::= { dot1dPortCapabilitiesTable 1 } Dot1dPortCapabilitiesEntry ::= SEQUENCE { Levi & Harrington Standards Track [Page 22]
RFC 4363 Bridge MIB Extensions January 2006 dot1dPortCapabilities BITS } dot1dPortCapabilities OBJECT-TYPE SYNTAX BITS { dot1qDot1qTagging(0), dot1qConfigurableAcceptableFrameTypes(1), dot1qIngressFiltering(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the parts of IEEE 802.1D and 802.1Q that are optional on a per-port basis, that are implemented by this device, and that are manageable through this MIB. dot1qDot1qTagging(0), -- supports 802.1Q VLAN tagging of -- frames and GVRP. dot1qConfigurableAcceptableFrameTypes(1), -- allows modified values of -- dot1qPortAcceptableFrameTypes. dot1qIngressFiltering(2) -- supports the discarding of any -- frame received on a Port whose -- VLAN classification does not -- include that Port in its Member -- set." REFERENCE "ISO/IEC 15802-3 Section 5.2, IEEE 802.1Q/D11 Section 5.2" ::= { dot1dPortCapabilitiesEntry 1 } -- ------------------------------------------------------------- -- the dot1dPriority subtree -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- Port Priority Table -- ------------------------------------------------------------- dot1dPortPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about every port that is associated with this transparent bridge." Levi & Harrington Standards Track [Page 23]
RFC 4363 Bridge MIB Extensions January 2006 ::= { dot1dPriority 1 } dot1dPortPriorityEntry OBJECT-TYPE SYNTAX Dot1dPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Default User Priorities for each port of a transparent bridge. This is indexed by dot1dBasePort." AUGMENTS { dot1dBasePortEntry } ::= { dot1dPortPriorityTable 1 } Dot1dPortPriorityEntry ::= SEQUENCE { dot1dPortDefaultUserPriority Integer32, dot1dPortNumTrafficClasses Integer32 } dot1dPortDefaultUserPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The default ingress User Priority for this port. This only has effect on media, such as Ethernet, that do not support native User Priority. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1dPortPriorityEntry 1 } dot1dPortNumTrafficClasses OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of egress traffic classes supported on this port. This object may optionally be read-only. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1dPortPriorityEntry 2 } -- ------------------------------------------------------------- -- User Priority Regeneration Table -- ------------------------------------------------------------- Levi & Harrington Standards Track [Page 24]
RFC 4363 Bridge MIB Extensions January 2006 dot1dUserPriorityRegenTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dUserPriorityRegenEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of Regenerated User Priorities for each received User Priority on each port of a bridge. The Regenerated User Priority value may be used to index the Traffic Class Table for each input port. This only has effect on media that support native User Priority. The default values for Regenerated User Priorities are the same as the User Priorities." REFERENCE "ISO/IEC 15802-3 Section 6.4" ::= { dot1dPriority 2 } dot1dUserPriorityRegenEntry OBJECT-TYPE SYNTAX Dot1dUserPriorityRegenEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping of incoming User Priority to a Regenerated User Priority." INDEX { dot1dBasePort, dot1dUserPriority } ::= { dot1dUserPriorityRegenTable 1 } Dot1dUserPriorityRegenEntry ::= SEQUENCE { dot1dUserPriority Integer32, dot1dRegenUserPriority Integer32 } dot1dUserPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The User Priority for a frame received on this port." ::= { dot1dUserPriorityRegenEntry 1 } dot1dRegenUserPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The Regenerated User Priority that the incoming User Levi & Harrington Standards Track [Page 25]
RFC 4363 Bridge MIB Extensions January 2006 Priority is mapped to for this port. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1dUserPriorityRegenEntry 2 } -- ------------------------------------------------------------- -- Traffic Class Table -- ------------------------------------------------------------- dot1dTrafficClassTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dTrafficClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..(dot1dPortNumTrafficClasses-1))." REFERENCE "ISO/IEC 15802-3 Table 7-2" ::= { dot1dPriority 3 } dot1dTrafficClassEntry OBJECT-TYPE SYNTAX Dot1dTrafficClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User Priority to Traffic Class mapping." INDEX { dot1dBasePort, dot1dTrafficClassPriority } ::= { dot1dTrafficClassTable 1 } Dot1dTrafficClassEntry ::= SEQUENCE { dot1dTrafficClassPriority Integer32, dot1dTrafficClass Integer32 } dot1dTrafficClassPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. Levi & Harrington Standards Track [Page 26]
RFC 4363 Bridge MIB Extensions January 2006 For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port. For untagged frames received from non-Ethernet media, this value is equal to the dot1dRegenUserPriority value for the ingress port and media-specific user priority." ::= { dot1dTrafficClassEntry 1 } dot1dTrafficClass OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The Traffic Class the received frame is mapped to. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1dTrafficClassEntry 2 } -- ------------------------------------------------------------- -- Outbound Access Priority Table -- ------------------------------------------------------------- dot1dPortOutboundAccessPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortOutboundAccessPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table mapping Regenerated User Priority to Outbound Access Priority. This is a fixed mapping for all port types, with two options for 802.5 Token Ring." REFERENCE "ISO/IEC 15802-3 Table 7-3" ::= { dot1dPriority 4 } dot1dPortOutboundAccessPriorityEntry OBJECT-TYPE SYNTAX Dot1dPortOutboundAccessPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Regenerated User Priority to Outbound Access Priority mapping." INDEX { dot1dBasePort, dot1dRegenUserPriority } ::= { dot1dPortOutboundAccessPriorityTable 1 } Dot1dPortOutboundAccessPriorityEntry ::= SEQUENCE { Levi & Harrington Standards Track [Page 27]
RFC 4363 Bridge MIB Extensions January 2006 dot1dPortOutboundAccessPriority Integer32 } dot1dPortOutboundAccessPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "The Outbound Access Priority the received frame is mapped to." ::= { dot1dPortOutboundAccessPriorityEntry 1 } -- ------------------------------------------------------------- -- the dot1dGarp subtree -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- The GARP Port Table -- ------------------------------------------------------------- dot1dPortGarpTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortGarpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of GARP control information about every bridge port. This is indexed by dot1dBasePort." ::= { dot1dGarp 1 } dot1dPortGarpEntry OBJECT-TYPE SYNTAX Dot1dPortGarpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "GARP control information for a bridge port." AUGMENTS { dot1dBasePortEntry } ::= { dot1dPortGarpTable 1 } Dot1dPortGarpEntry ::= SEQUENCE { dot1dPortGarpJoinTime TimeInterval, dot1dPortGarpLeaveTime TimeInterval, dot1dPortGarpLeaveAllTime TimeInterval } Levi & Harrington Standards Track [Page 28]
RFC 4363 Bridge MIB Extensions January 2006 dot1dPortGarpJoinTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP Join time, in centiseconds. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { 20 } ::= { dot1dPortGarpEntry 1 } dot1dPortGarpLeaveTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP Leave time, in centiseconds. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { 60 } ::= { dot1dPortGarpEntry 2 } dot1dPortGarpLeaveAllTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP LeaveAll time, in centiseconds. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { 1000 } ::= { dot1dPortGarpEntry 3 } -- ------------------------------------------------------------- -- The GMRP Port Configuration and Status Table -- ------------------------------------------------------------- dot1dPortGmrpTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortGmrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of GMRP control and status information about every bridge port. Augments the dot1dBasePortTable." ::= { dot1dGmrp 1 } Levi & Harrington Standards Track [Page 29]
RFC 4363 Bridge MIB Extensions January 2006 dot1dPortGmrpEntry OBJECT-TYPE SYNTAX Dot1dPortGmrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "GMRP control and status information for a bridge port." AUGMENTS { dot1dBasePortEntry } ::= { dot1dPortGmrpTable 1 } Dot1dPortGmrpEntry ::= SEQUENCE { dot1dPortGmrpStatus EnabledStatus, dot1dPortGmrpFailedRegistrations Counter32, dot1dPortGmrpLastPduOrigin MacAddress, dot1dPortRestrictedGroupRegistration TruthValue } dot1dPortGmrpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative state of GMRP operation on this port. The value enabled(1) indicates that GMRP is enabled on this port in all VLANs as long as dot1dGmrpStatus is also enabled(1). A value of disabled(2) indicates that GMRP is disabled on this port in all VLANs: any GMRP packets received will be silently discarded, and no GMRP registrations will be propagated from other ports. Setting this to a value of enabled(1) will be stored by the agent but will only take effect on the GMRP protocol operation if dot1dGmrpStatus also indicates the value enabled(1). This object affects all GMRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GMRP state machines on this port. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { enabled } ::= { dot1dPortGmrpEntry 1 } dot1dPortGmrpFailedRegistrations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only Levi & Harrington Standards Track [Page 30]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "The total number of failed GMRP registrations, for any reason, in all VLANs, on this port." ::= { dot1dPortGmrpEntry 2 } dot1dPortGmrpLastPduOrigin OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Source MAC Address of the last GMRP message received on this port." ::= { dot1dPortGmrpEntry 3 } dot1dPortRestrictedGroupRegistration OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The state of Restricted Group Registration on this port. If the value of this control is true(1), then creation of a new dynamic entry is permitted only if there is a Static Filtering Entry for the VLAN concerned, in which the Registrar Administrative Control value is Normal Registration. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1t clause 10.3.2.3, 14.10.1.3." DEFVAL { false } ::= { dot1dPortGmrpEntry 4 } -- ------------------------------------------------------------- -- High-Capacity Port Table for Transparent Bridges -- ------------------------------------------------------------- dot1dTpHCPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dTpHCPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about every high- capacity port that is associated with this transparent bridge." ::= { dot1dTp 5 } Levi & Harrington Standards Track [Page 31]
RFC 4363 Bridge MIB Extensions January 2006 dot1dTpHCPortEntry OBJECT-TYPE SYNTAX Dot1dTpHCPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics information for each high-capacity port of a transparent bridge." INDEX { dot1dTpPort } ::= { dot1dTpHCPortTable 1 } Dot1dTpHCPortEntry ::= SEQUENCE { dot1dTpHCPortInFrames Counter64, dot1dTpHCPortOutFrames Counter64, dot1dTpHCPortInDiscards Counter64 } dot1dTpHCPortInFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1dTpHCPortEntry 1 } dot1dTpHCPortOutFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" Levi & Harrington Standards Track [Page 32]
RFC 4363 Bridge MIB Extensions January 2006 ::= { dot1dTpHCPortEntry 2 } dot1dTpHCPortInDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of valid frames that have been received by this port from its segment that were discarded (i.e., filtered) by the Forwarding Process." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1dTpHCPortEntry 3 } -- ---------------------------------------------------- -- Upper part of High-Capacity Port Table for Transparent Bridges -- ---------------------------------------------------- dot1dTpPortOverflowTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dTpPortOverflowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the most-significant bits of statistics counters for ports that are associated with this transparent bridge that are on high-capacity interfaces, as defined in the conformance clauses for this table. This table is provided as a way to read 64-bit counters for agents that support only SNMPv1. Note that the reporting of most-significant and least-significant counter bits separately runs the risk of missing an overflow of the lower bits in the interval between sampling. The manager must be aware of this possibility, even within the same varbindlist, when interpreting the results of a request or asynchronous notification." ::= { dot1dTp 6 } dot1dTpPortOverflowEntry OBJECT-TYPE SYNTAX Dot1dTpPortOverflowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The most significant bits of statistics counters for a high- capacity interface of a transparent bridge. Each object is associated with a corresponding object in dot1dTpPortTable that indicates the least significant bits of the counter." INDEX { dot1dTpPort } Levi & Harrington Standards Track [Page 33]
RFC 4363 Bridge MIB Extensions January 2006 ::= { dot1dTpPortOverflowTable 1 } Dot1dTpPortOverflowEntry ::= SEQUENCE { dot1dTpPortInOverflowFrames Counter32, dot1dTpPortOutOverflowFrames Counter32, dot1dTpPortInOverflowDiscards Counter32 } dot1dTpPortInOverflowFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1dTpPortInFrames counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1dTpPortOverflowEntry 1 } dot1dTpPortOutOverflowFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1dTpPortOutFrames counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1dTpPortOverflowEntry 2 } dot1dTpPortInOverflowDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1dTpPortInDiscards counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1dTpPortOverflowEntry 3 } -- ------------------------------------------------------------- -- IEEE 802.1p MIB - Conformance Information -- ------------------------------------------------------------- Levi & Harrington Standards Track [Page 34]
RFC 4363 Bridge MIB Extensions January 2006 pBridgeConformance OBJECT IDENTIFIER ::= { pBridgeMIB 2 } pBridgeGroups OBJECT IDENTIFIER ::= { pBridgeConformance 1 } pBridgeCompliances OBJECT IDENTIFIER ::= { pBridgeConformance 2 } -- ------------------------------------------------------------- -- units of conformance -- ------------------------------------------------------------- pBridgeExtCapGroup OBJECT-GROUP OBJECTS { dot1dDeviceCapabilities, dot1dPortCapabilities } STATUS current DESCRIPTION "A collection of objects indicating the optional capabilities of the device." ::= { pBridgeGroups 1 } pBridgeDeviceGmrpGroup OBJECT-GROUP OBJECTS { dot1dGmrpStatus } STATUS current DESCRIPTION "A collection of objects providing device-level control for the Multicast Filtering extended bridge services." ::= { pBridgeGroups 2 } pBridgeDevicePriorityGroup OBJECT-GROUP OBJECTS { dot1dTrafficClassesEnabled } STATUS current DESCRIPTION "A collection of objects providing device-level control for the Priority services." ::= { pBridgeGroups 3 } pBridgeDefaultPriorityGroup OBJECT-GROUP OBJECTS { dot1dPortDefaultUserPriority } STATUS current DESCRIPTION Levi & Harrington Standards Track [Page 35]
RFC 4363 Bridge MIB Extensions January 2006 "A collection of objects defining the User Priority applicable to each port for media that do not support native User Priority." ::= { pBridgeGroups 4 } pBridgeRegenPriorityGroup OBJECT-GROUP OBJECTS { dot1dRegenUserPriority } STATUS current DESCRIPTION "A collection of objects defining the User Priorities applicable to each port for media that support native User Priority." ::= { pBridgeGroups 5 } pBridgePriorityGroup OBJECT-GROUP OBJECTS { dot1dPortNumTrafficClasses, dot1dTrafficClass } STATUS current DESCRIPTION "A collection of objects defining the traffic classes within a bridge for each evaluated User Priority." ::= { pBridgeGroups 6 } pBridgeAccessPriorityGroup OBJECT-GROUP OBJECTS { dot1dPortOutboundAccessPriority } STATUS current DESCRIPTION "A collection of objects defining the media-dependent outbound access level for each priority." ::= { pBridgeGroups 7 } pBridgePortGarpGroup OBJECT-GROUP OBJECTS { dot1dPortGarpJoinTime, dot1dPortGarpLeaveTime, dot1dPortGarpLeaveAllTime } STATUS current DESCRIPTION "A collection of objects providing port level control and status information for GARP operation." ::= { pBridgeGroups 8 } Levi & Harrington Standards Track [Page 36]
RFC 4363 Bridge MIB Extensions January 2006 pBridgePortGmrpGroup OBJECT-GROUP OBJECTS { dot1dPortGmrpStatus, dot1dPortGmrpFailedRegistrations, dot1dPortGmrpLastPduOrigin } STATUS deprecated DESCRIPTION "A collection of objects providing port level control and status information for GMRP operation." ::= { pBridgeGroups 9 } pBridgeHCPortGroup OBJECT-GROUP OBJECTS { dot1dTpHCPortInFrames, dot1dTpHCPortOutFrames, dot1dTpHCPortInDiscards } STATUS current DESCRIPTION "A collection of objects providing 64-bit statistics counters for high-capacity bridge ports." ::= { pBridgeGroups 10 } pBridgePortOverflowGroup OBJECT-GROUP OBJECTS { dot1dTpPortInOverflowFrames, dot1dTpPortOutOverflowFrames, dot1dTpPortInOverflowDiscards } STATUS current DESCRIPTION "A collection of objects providing overflow statistics counters for high-capacity bridge ports." ::= { pBridgeGroups 11 } pBridgePortGmrpGroup2 OBJECT-GROUP OBJECTS { dot1dPortGmrpStatus, dot1dPortGmrpFailedRegistrations, dot1dPortGmrpLastPduOrigin, dot1dPortRestrictedGroupRegistration } STATUS current DESCRIPTION "A collection of objects providing port level control and status information for GMRP operation." ::= { pBridgeGroups 12 } Levi & Harrington Standards Track [Page 37]
RFC 4363 Bridge MIB Extensions January 2006 -- ------------------------------------------------------------- -- compliance statements -- ------------------------------------------------------------- pBridgeCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for device support of Priority and Multicast Filtering extended bridging services." MODULE MANDATORY-GROUPS { pBridgeExtCapGroup } GROUP pBridgeDeviceGmrpGroup DESCRIPTION "This group is mandatory for devices supporting the GMRP application, defined by IEEE 802.1D Extended Filtering Services." GROUP pBridgeDevicePriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D." GROUP pBridgeDefaultPriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by the extended bridge services with media types, such as Ethernet, that do not support native User Priority." GROUP pBridgeRegenPriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D and that have interface media types that support native User Priority, e.g., IEEE 802.5." GROUP pBridgePriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D." GROUP pBridgeAccessPriorityGroup DESCRIPTION "This group is optional and is relevant only for devices supporting the priority forwarding operations defined by Levi & Harrington Standards Track [Page 38]
RFC 4363 Bridge MIB Extensions January 2006 IEEE 802.1D and that have interface media types that support native Access Priority, e.g., IEEE 802.5." GROUP pBridgePortGarpGroup DESCRIPTION "This group is mandatory for devices supporting any of the GARP applications: e.g., GMRP, defined by the extended filtering services of 802.1D; or GVRP, defined by 802.1Q (refer to the Q-BRIDGE-MIB for conformance statements for GVRP)." GROUP pBridgePortGmrpGroup DESCRIPTION "This group is mandatory for devices supporting the GMRP application, as defined by IEEE 802.1D Extended Filtering Services." GROUP pBridgeHCPortGroup DESCRIPTION "Support for this group in a device is mandatory for those bridge ports that map to network interfaces that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." GROUP pBridgePortOverflowGroup DESCRIPTION "Support for this group in a device is mandatory for those bridge ports that map to network interfaces that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." OBJECT dot1dPortNumTrafficClasses MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT dot1dTrafficClass MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT dot1dRegenUserPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pBridgeCompliances 1 } Levi & Harrington Standards Track [Page 39]
RFC 4363 Bridge MIB Extensions January 2006 pBridgeCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for device support of Priority and Multicast Filtering extended bridging services." MODULE MANDATORY-GROUPS { pBridgeExtCapGroup } GROUP pBridgeDeviceGmrpGroup DESCRIPTION "This group is mandatory for devices supporting the GMRP application, defined by IEEE 802.1D Extended Filtering Services." GROUP pBridgeDevicePriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D." GROUP pBridgeDefaultPriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by the extended bridge services with media types, such as Ethernet, that do not support native User Priority." GROUP pBridgeRegenPriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D and that have interface media types that support native User Priority, e.g., IEEE 802.5." GROUP pBridgePriorityGroup DESCRIPTION "This group is mandatory only for devices supporting the priority forwarding operations defined by IEEE 802.1D." GROUP pBridgeAccessPriorityGroup DESCRIPTION "This group is optional and is relevant only for devices supporting the priority forwarding operations defined by IEEE 802.1D and that have interface media types that support native Access Priority, e.g., IEEE 802.5." GROUP pBridgePortGarpGroup Levi & Harrington Standards Track [Page 40]
RFC 4363 Bridge MIB Extensions January 2006 DESCRIPTION "This group is mandatory for devices supporting any of the GARP applications: e.g., GMRP, defined by the extended filtering services of 802.1D; or GVRP, defined by 802.1Q (refer to the Q-BRIDGE-MIB for conformance statements for GVRP)." GROUP pBridgePortGmrpGroup2 DESCRIPTION "This group is mandatory for devices supporting the GMRP application, as defined by IEEE 802.1D Extended Filtering Services." GROUP pBridgeHCPortGroup DESCRIPTION "Support for this group in a device is mandatory for those bridge ports that map to network interfaces that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." GROUP pBridgePortOverflowGroup DESCRIPTION "Support for this group in a device is mandatory for those bridge ports that map to network interfaces that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." OBJECT dot1dPortNumTrafficClasses MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT dot1dTrafficClass MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT dot1dRegenUserPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pBridgeCompliances 2 } END Levi & Harrington Standards Track [Page 41]
RFC 4363 Bridge MIB Extensions January 2006 5. Definitions for Virtual Bridge MIB Q-BRIDGE-MIB DEFINITIONS ::= BEGIN -- ------------------------------------------------------------- -- MIB for IEEE 802.1Q Devices -- ------------------------------------------------------------- IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Counter64, Unsigned32, TimeTicks, Integer32 FROM SNMPv2-SMI RowStatus, TruthValue, TEXTUAL-CONVENTION, MacAddress FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF dot1dBridge, dot1dBasePortEntry, dot1dBasePort FROM BRIDGE-MIB EnabledStatus FROM P-BRIDGE-MIB TimeFilter FROM RMON2-MIB; qBridgeMIB MODULE-IDENTITY LAST-UPDATED "200601090000Z" ORGANIZATION "IETF Bridge MIB Working Group" CONTACT-INFO "Email: Bridge-mib@ietf.org ietfmibs@ops.ietf.org David Levi Postal: Nortel Networks 4655 Great America Parkway Santa Clara, CA 95054 USA Phone: +1 865 686 0432 Email: dlevi@nortel.com David Harrington Postal: Effective Software 50 Harding Rd. Portsmouth, NH 03801 USA Phone: +1 603 436 8634 Email: ietfdbh@comcast.net Levi & Harrington Standards Track [Page 42]
RFC 4363 Bridge MIB Extensions January 2006 Les Bell Postal: Hemel Hempstead, Herts. HP2 7YU UK Email: elbell@ntlworld.com Andrew Smith Postal: Beijing Harbour Networks Jiuling Building 21 North Xisanhuan Ave. Beijing, 100089 PRC Fax: +1 415 345 1827 Email: ah_smith@acm.org Paul Langille Postal: Newbridge Networks 5 Corporate Drive Andover, MA 01810 USA Phone: +1 978 691 4665 Email: langille@newbridge.com Anil Rijhsinghani Postal: Accton Technology Corporation 5 Mount Royal Ave Marlboro, MA 01752 USA Phone: Email: anil@accton.com Keith McCloghrie Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Phone: +1 408 526 5260 Email: kzm@cisco.com" DESCRIPTION "The VLAN Bridge MIB module for managing Virtual Bridged Local Area Networks, as defined by IEEE 802.1Q-2003, including Restricted Vlan Registration defined by IEEE 802.1u-2001 and Vlan Classification defined by IEEE 802.1v-2001. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4363; See the RFC itself for full legal notices." REVISION "200601090000Z" Levi & Harrington Standards Track [Page 43]
RFC 4363 Bridge MIB Extensions January 2006 DESCRIPTION "Added Vlan TEXTUAL-CONVENTIONs, dot1qPortRestrictedVlanRegistration, dot1vProtocol subtree, qBridgeClassificationDeviceGroup, qBridgePortGroup2, qBridgeClassificationPortGroup, and qBridgeCompliance2. Clarified dot1qForwardAllStaticPorts, qPortAcceptableFrameTypes, and qBridgeCompliance. Deprecated qBridgePortGroup and qBridgeCompliance." REVISION "199908250000Z" DESCRIPTION "The VLAN Bridge MIB module for managing Virtual Bridged Local Area Networks, as defined by IEEE 802.1Q-1998. Initial version, published as RFC 2674." ::= { dot1dBridge 7 } qBridgeMIBObjects OBJECT IDENTIFIER ::= { qBridgeMIB 1 } -- ------------------------------------------------------------- -- Textual Conventions -- ------------------------------------------------------------- PortList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1', then that port is included in the set of ports; the port is not included if its bit has a value of '0'." SYNTAX OCTET STRING VlanIndex ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A value used to index per-VLAN tables: values of 0 and 4095 are not permitted. If the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095, Levi & Harrington Standards Track [Page 44]
RFC 4363 Bridge MIB Extensions January 2006 then it represents a VLAN with scope local to the particular agent, i.e., one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q, but it is convenient to be able to manage them in the same way using this MIB." SYNTAX Unsigned32 VlanId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The VLAN-ID that uniquely identifies a VLAN. This is the 12-bit VLAN-ID used in the VLAN Tag header. The range is defined by the REFERENCEd specification." REFERENCE "IEEE Std 802.1Q 2003 Edition, Virtual Bridged Local Area Networks." SYNTAX Integer32 (1..4094) VlanIdOrAny ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The VLAN-ID that uniquely identifies a specific VLAN, or any VLAN. The special value of 4095 is used to indicate a wildcard, i.e., any VLAN. This can be used in any situation where an object or table entry must refer either to a specific VLAN or to any VLAN. Note that a MIB object that is defined using this TEXTUAL-CONVENTION should clarify the meaning of 'any VLAN' (i.e., the special value 4095)." SYNTAX Integer32 (1..4094 | 4095) VlanIdOrNone ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The VLAN-ID that uniquely identifies a specific VLAN, or no VLAN. The special value of zero is used to indicate that no VLAN-ID is present or used. This can be used in any situation where an object or a table entry must refer either to a specific VLAN, or to no VLAN. Note that a MIB object that is defined using this TEXTUAL-CONVENTION should clarify the meaning of 'no VLAN' (i.e., the special value 0)." SYNTAX Integer32 (0 | 1..4094) Levi & Harrington Standards Track [Page 45]
RFC 4363 Bridge MIB Extensions January 2006 VlanIdOrAnyOrNone ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The VLAN-ID that uniquely identifies a specific VLAN, any VLAN, or no VLAN. The special values 0 and 4095 have the same meaning as described in the VlanIdOrAny and VlanIdOrNone TEXTUAL-CONVENTIONs. Note that a MIB object that is defined using this TEXTUAL-CONVENTION should clarify the meaning of 'any VLAN' and 'no VLAN' (i.e., the special values 0 and 4095)." SYNTAX Integer32 (0 | 1..4094 | 4095) -- ------------------------------------------------------------- -- subtrees in the Q-BRIDGE MIB -- ------------------------------------------------------------- dot1qBase OBJECT IDENTIFIER ::= { qBridgeMIBObjects 1 } dot1qTp OBJECT IDENTIFIER ::= { qBridgeMIBObjects 2 } dot1qStatic OBJECT IDENTIFIER ::= { qBridgeMIBObjects 3 } dot1qVlan OBJECT IDENTIFIER ::= { qBridgeMIBObjects 4 } dot1vProtocol OBJECT IDENTIFIER ::= { qBridgeMIBObjects 5 } -- ------------------------------------------------------------- -- dot1qBase subtree -- ------------------------------------------------------------- dot1qVlanVersionNumber OBJECT-TYPE SYNTAX INTEGER { version1(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version number of IEEE 802.1Q that this device supports." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" ::= { dot1qBase 1 } dot1qMaxVlanId OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum IEEE 802.1Q VLAN-ID that this device Levi & Harrington Standards Track [Page 46]
RFC 4363 Bridge MIB Extensions January 2006 supports." REFERENCE "IEEE 802.1Q/D11 Section 9.3.2.3" ::= { dot1qBase 2 } dot1qMaxSupportedVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IEEE 802.1Q VLANs that this device supports." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" ::= { dot1qBase 3 } dot1qNumVlans OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of IEEE 802.1Q VLANs that are configured in this device." REFERENCE "IEEE 802.1Q/D11 Section 12.7.1.1" ::= { dot1qBase 4 } dot1qGvrpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status requested by management for GVRP. The value enabled(1) indicates that GVRP should be enabled on this device, on all ports for which it has not been specifically disabled. When disabled(2), GVRP is disabled on all ports, and all GVRP packets will be forwarded transparently. This object affects all GVRP Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on all ports. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { enabled } ::= { dot1qBase 5 } -- ------------------------------------------------------------- Levi & Harrington Standards Track [Page 47]
RFC 4363 Bridge MIB Extensions January 2006 -- the dot1qTp subtree -- ------------------------------------------------------------- -- ------------------------------------------------------------- -- the current Filtering Database Table -- ------------------------------------------------------------- dot1qFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains configuration and control information for each Filtering Database currently operating on this device. Entries in this table appear automatically when VLANs are assigned FDB IDs in the dot1qVlanCurrentTable." ::= { dot1qTp 1 } dot1qFdbEntry OBJECT-TYPE SYNTAX Dot1qFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a specific Filtering Database." INDEX { dot1qFdbId } ::= { dot1qFdbTable 1 } Dot1qFdbEntry ::= SEQUENCE { dot1qFdbId Unsigned32, dot1qFdbDynamicCount Counter32 } dot1qFdbId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identity of this Filtering Database." ::= { dot1qFdbEntry 1 } dot1qFdbDynamicCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current Levi & Harrington Standards Track [Page 48]
RFC 4363 Bridge MIB Extensions January 2006 DESCRIPTION "The current number of dynamic entries in this Filtering Database." REFERENCE "IEEE 802.1Q/D11 Section 12.7.1.1.3" ::= { dot1qFdbEntry 2 } -- ------------------------------------------------------------- -- Multiple Forwarding Databases for 802.1Q Transparent Devices -- This table is an alternative to the dot1dTpFdbTable, -- previously defined for 802.1D devices that only support a -- single Forwarding Database. -- ------------------------------------------------------------- dot1qTpFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qTpFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7" ::= { dot1qTp 2 } dot1qTpFdbEntry OBJECT-TYPE SYNTAX Dot1qTpFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information." INDEX { dot1qFdbId, dot1qTpFdbAddress } ::= { dot1qTpFdbTable 1 } Dot1qTpFdbEntry ::= SEQUENCE { dot1qTpFdbAddress MacAddress, dot1qTpFdbPort Integer32, dot1qTpFdbStatus INTEGER } Levi & Harrington Standards Track [Page 49]
RFC 4363 Bridge MIB Extensions January 2006 dot1qTpFdbAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unicast MAC address for which the device has forwarding and/or filtering information." ::= { dot1qTpFdbEntry 1 } dot1qTpFdbPort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the device does have some forwarding/filtering information about this address (e.g., in the dot1qStaticUnicastTable). Implementors are encouraged to assign the port value to this object whenever it is learned, even for addresses for which the corresponding value of dot1qTpFdbStatus is not learned(3)." ::= { dot1qTpFdbEntry 2 } dot1qTpFdbStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), learned(3), self(4), mgmt(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this entry. The meanings of the values are: other(1) - none of the following. This may include the case where some other MIB object (not the corresponding instance of dot1qTpFdbPort, nor an entry in the dot1qStaticUnicastTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dot1qTpFdbAddress are being forwarded. invalid(2) - this entry is no longer valid (e.g., it Levi & Harrington Standards Track [Page 50]
RFC 4363 Bridge MIB Extensions January 2006 was learned but has since aged out), but has not yet been flushed from the table. learned(3) - the value of the corresponding instance of dot1qTpFdbPort was learned and is being used. self(4) - the value of the corresponding instance of dot1qTpFdbAddress represents one of the device's addresses. The corresponding instance of dot1qTpFdbPort indicates which of the device's ports has this address. mgmt(5) - the value of the corresponding instance of dot1qTpFdbAddress is also the value of an existing instance of dot1qStaticAddress." ::= { dot1qTpFdbEntry 3 } -- ------------------------------------------------------------- -- Dynamic Group Registration Table -- ------------------------------------------------------------- dot1qTpGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qTpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing filtering information for VLANs configured into the bridge by (local or network) management, or learned dynamically, specifying the set of ports to which frames received on a VLAN for this FDB and containing a specific Group destination address are allowed to be forwarded." ::= { dot1qTp 3 } dot1qTpGroupEntry OBJECT-TYPE SYNTAX Dot1qTpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Filtering information configured into the bridge by management, or learned dynamically, specifying the set of ports to which frames received on a VLAN and containing a specific Group destination address are allowed to be forwarded. The subset of these ports learned dynamically is also provided." INDEX { dot1qVlanIndex, dot1qTpGroupAddress } ::= { dot1qTpGroupTable 1 } Dot1qTpGroupEntry ::= SEQUENCE { dot1qTpGroupAddress Levi & Harrington Standards Track [Page 51]
RFC 4363 Bridge MIB Extensions January 2006 MacAddress, dot1qTpGroupEgressPorts PortList, dot1qTpGroupLearnt PortList } dot1qTpGroupAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination Group MAC address in a frame to which this entry's filtering information applies." ::= { dot1qTpGroupEntry 1 } dot1qTpGroupEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The complete set of ports, in this VLAN, to which frames destined for this Group MAC address are currently being explicitly forwarded. This does not include ports for which this address is only implicitly forwarded, in the dot1qForwardAllPorts list." ::= { dot1qTpGroupEntry 2 } dot1qTpGroupLearnt OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The subset of ports in dot1qTpGroupEgressPorts that were learned by GMRP or some other dynamic mechanism, in this Filtering database." ::= { dot1qTpGroupEntry 3 } -- ------------------------------------------------------------- -- Service Requirements subtree -- ------------------------------------------------------------- dot1qForwardAllTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qForwardAllEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing forwarding information for each Levi & Harrington Standards Track [Page 52]
RFC 4363 Bridge MIB Extensions January 2006 VLAN, specifying the set of ports to which forwarding of all multicasts applies, configured statically by management or dynamically by GMRP. An entry appears in this table for all VLANs that are currently instantiated." REFERENCE "IEEE 802.1Q/D11 Section 12.7.2, 12.7.7" ::= { dot1qTp 4 } dot1qForwardAllEntry OBJECT-TYPE SYNTAX Dot1qForwardAllEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Forwarding information for a VLAN, specifying the set of ports to which all multicasts should be forwarded, configured statically by management or dynamically by GMRP." INDEX { dot1qVlanIndex } ::= { dot1qForwardAllTable 1 } Dot1qForwardAllEntry ::= SEQUENCE { dot1qForwardAllPorts PortList, dot1qForwardAllStaticPorts PortList, dot1qForwardAllForbiddenPorts PortList } dot1qForwardAllPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The complete set of ports in this VLAN to which all multicast group-addressed frames are to be forwarded. This includes ports for which this need has been determined dynamically by GMRP, or configured statically by management." ::= { dot1qForwardAllEntry 1 } dot1qForwardAllStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION Levi & Harrington Standards Track [Page 53]
RFC 4363 Bridge MIB Extensions January 2006 "The set of ports configured by management in this VLAN to which all multicast group-addressed frames are to be forwarded. Ports entered in this list will also appear in the complete set shown by dot1qForwardAllPorts. This value will be restored after the device is reset. This only applies to ports that are members of the VLAN, defined by dot1qVlanCurrentEgressPorts. A port may not be added in this set if it is already a member of the set of ports in dot1qForwardAllForbiddenPorts. The default value is a string of ones of appropriate length, to indicate the standard behaviour of using basic filtering services, i.e., forward all multicasts to all ports. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qForwardAllEntry 2 } dot1qForwardAllForbiddenPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports configured by management in this VLAN for which the Service Requirement attribute Forward All Multicast Groups may not be dynamically registered by GMRP. This value will be restored after the device is reset. A port may not be added in this set if it is already a member of the set of ports in dot1qForwardAllStaticPorts. The default value is a string of zeros of appropriate length. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qForwardAllEntry 3 } dot1qForwardUnregisteredTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qForwardUnregisteredEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing forwarding information for each VLAN, specifying the set of ports to which forwarding of multicast group-addressed frames for which no more specific forwarding information applies. This is configured statically by management and determined dynamically by GMRP. An entry appears in this table for all VLANs that are currently instantiated." Levi & Harrington Standards Track [Page 54]
RFC 4363 Bridge MIB Extensions January 2006 REFERENCE "IEEE 802.1Q/D11 Section 12.7.2, 12.7.7" ::= { dot1qTp 5 } dot1qForwardUnregisteredEntry OBJECT-TYPE SYNTAX Dot1qForwardUnregisteredEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Forwarding information for a VLAN, specifying the set of ports to which all multicasts for which there is no more specific forwarding information shall be forwarded. This is configured statically by management or dynamically by GMRP." INDEX { dot1qVlanIndex } ::= { dot1qForwardUnregisteredTable 1 } Dot1qForwardUnregisteredEntry ::= SEQUENCE { dot1qForwardUnregisteredPorts PortList, dot1qForwardUnregisteredStaticPorts PortList, dot1qForwardUnregisteredForbiddenPorts PortList } dot1qForwardUnregisteredPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The complete set of ports in this VLAN to which multicast group-addressed frames for which there is no more specific forwarding information will be forwarded. This includes ports for which this need has been determined dynamically by GMRP, or configured statically by management." ::= { dot1qForwardUnregisteredEntry 1 } dot1qForwardUnregisteredStaticPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports configured by management, in this VLAN, to which multicast group-addressed frames for which there is no more specific forwarding information Levi & Harrington Standards Track [Page 55]
RFC 4363 Bridge MIB Extensions January 2006 are to be forwarded. Ports entered in this list will also appear in the complete set shown by dot1qForwardUnregisteredPorts. This value will be restored after the device is reset. A port may not be added in this set if it is already a member of the set of ports in dot1qForwardUnregisteredForbiddenPorts. The default value is a string of zeros of appropriate length, although this has no effect with the default value of dot1qForwardAllStaticPorts. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qForwardUnregisteredEntry 2 } dot1qForwardUnregisteredForbiddenPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports configured by management in this VLAN for which the Service Requirement attribute Forward Unregistered Multicast Groups may not be dynamically registered by GMRP. This value will be restored after the device is reset. A port may not be added in this set if it is already a member of the set of ports in dot1qForwardUnregisteredStaticPorts. The default value is a string of zeros of appropriate length. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qForwardUnregisteredEntry 3 } -- ------------------------------------------------------------- -- The Static (Destination-Address Filtering) Database -- ------------------------------------------------------------- dot1qStaticUnicastTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qStaticUnicastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing filtering information for Unicast MAC addresses for each Filtering Database, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific unicast destination addresses are allowed to be forwarded. A value of zero in this table (as the port number from Levi & Harrington Standards Track [Page 56]
RFC 4363 Bridge MIB Extensions January 2006 which frames with a specific destination address are received) is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast addresses only." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7, ISO/IEC 15802-3 Section 7.9.1" ::= { dot1qStatic 1 } dot1qStaticUnicastEntry OBJECT-TYPE SYNTAX Dot1qStaticUnicastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific unicast destination address are allowed to be forwarded." INDEX { dot1qFdbId, dot1qStaticUnicastAddress, dot1qStaticUnicastReceivePort } ::= { dot1qStaticUnicastTable 1 } Dot1qStaticUnicastEntry ::= SEQUENCE { dot1qStaticUnicastAddress MacAddress, dot1qStaticUnicastReceivePort Integer32, dot1qStaticUnicastAllowedToGoTo PortList, dot1qStaticUnicastStatus INTEGER } dot1qStaticUnicastAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a unicast address." ::= { dot1qStaticUnicastEntry 1 } Levi & Harrington Standards Track [Page 57]
RFC 4363 Bridge MIB Extensions January 2006 dot1qStaticUnicastReceivePort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Either the value '0' or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the device for which there is no other applicable entry." ::= { dot1qStaticUnicastEntry 2 } dot1qStaticUnicastAllowedToGoTo OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports for which a frame with a specific unicast address will be flooded in the event that it has not been learned. It also specifies the set of ports on which a specific unicast address may be dynamically learned. The dot1qTpFdbTable will have an equivalent entry with a dot1qTpFdbPort value of '0' until this address has been learned, at which point it will be updated with the port the address has been seen on. This only applies to ports that are members of the VLAN, defined by dot1qVlanCurrentEgressPorts. The default value of this object is a string of ones of appropriate length. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1Q/D11 Table 8-5, ISO/IEC 15802-3 Table 7-5" ::= { dot1qStaticUnicastEntry 3 } dot1qStaticUnicastStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. other(1) - this entry is currently in use, but Levi & Harrington Standards Track [Page 58]
RFC 4363 Bridge MIB Extensions January 2006 the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { permanent } ::= { dot1qStaticUnicastEntry 4 } dot1qStaticMulticastTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qStaticMulticastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing filtering information for Multicast and Broadcast MAC addresses for each VLAN, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific Multicast and Broadcast destination addresses are allowed to be forwarded. A value of zero in this table (as the port number from which frames with a specific destination address are received) is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for Multicast and Broadcast addresses only." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7, ISO/IEC 15802-3 Section 7.9.1" ::= { dot1qStatic 2 } dot1qStaticMulticastEntry OBJECT-TYPE SYNTAX Dot1qStaticMulticastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from this specific port Levi & Harrington Standards Track [Page 59]
RFC 4363 Bridge MIB Extensions January 2006 for this VLAN and containing this Multicast or Broadcast destination address are allowed to be forwarded." INDEX { dot1qVlanIndex, dot1qStaticMulticastAddress, dot1qStaticMulticastReceivePort } ::= { dot1qStaticMulticastTable 1 } Dot1qStaticMulticastEntry ::= SEQUENCE { dot1qStaticMulticastAddress MacAddress, dot1qStaticMulticastReceivePort Integer32, dot1qStaticMulticastStaticEgressPorts PortList, dot1qStaticMulticastForbiddenEgressPorts PortList, dot1qStaticMulticastStatus INTEGER } dot1qStaticMulticastAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address." ::= { dot1qStaticMulticastEntry 1 } dot1qStaticMulticastReceivePort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Either the value '0' or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the device for which there is no other applicable entry." ::= { dot1qStaticMulticastEntry 2 } dot1qStaticMulticastStaticEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write Levi & Harrington Standards Track [Page 60]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information, e.g., from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qStaticMulticastEntry 3 } dot1qStaticMulticastForbiddenEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must not be forwarded, regardless of any dynamic information, e.g., from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastStaticEgressPorts. The default value of this object is a string of zeros of appropriate length. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qStaticMulticastEntry 4 } dot1qStaticMulticastStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates the status of this entry. other(1) - this entry is currently in use, but the conditions under which it will remain so differ from the following values. Levi & Harrington Standards Track [Page 61]
RFC 4363 Bridge MIB Extensions January 2006 invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { permanent } ::= { dot1qStaticMulticastEntry 5 } -- ------------------------------------------------------------- -- The Current VLAN Database -- ------------------------------------------------------------- dot1qVlanNumDeletes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a VLAN entry has been deleted from the dot1qVlanCurrentTable (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2." ::= { dot1qVlan 1 } dot1qVlanCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received." ::= { dot1qVlan 2 } dot1qVlanCurrentEntry OBJECT-TYPE SYNTAX Dot1qVlanCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a VLAN configured into the device by Levi & Harrington Standards Track [Page 62]
RFC 4363 Bridge MIB Extensions January 2006 (local or network) management, or dynamically created as a result of GVRP requests received." INDEX { dot1qVlanTimeMark, dot1qVlanIndex } ::= { dot1qVlanCurrentTable 1 } Dot1qVlanCurrentEntry ::= SEQUENCE { dot1qVlanTimeMark TimeFilter, dot1qVlanIndex VlanIndex, dot1qVlanFdbId Unsigned32, dot1qVlanCurrentEgressPorts PortList, dot1qVlanCurrentUntaggedPorts PortList, dot1qVlanStatus INTEGER, dot1qVlanCreationTime TimeTicks } dot1qVlanTimeMark OBJECT-TYPE SYNTAX TimeFilter MAX-ACCESS not-accessible STATUS current DESCRIPTION "A TimeFilter for this entry. See the TimeFilter textual convention to see how this works." ::= { dot1qVlanCurrentEntry 1 } dot1qVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-ID or other identifier referring to this VLAN." ::= { dot1qVlanCurrentEntry 2 } dot1qVlanFdbId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Filtering Database used by this VLAN. This is one of the dot1qFdbId values in the dot1qFdbTable. This value is allocated automatically by the device whenever Levi & Harrington Standards Track [Page 63]
RFC 4363 Bridge MIB Extensions January 2006 the VLAN is created: either dynamically by GVRP, or by management, in dot1qVlanStaticTable. Allocation of this value follows the learning constraints defined for this VLAN in dot1qLearningConstraintsTable." ::= { dot1qVlanCurrentEntry 3 } dot1qVlanCurrentEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports that are transmitting traffic for this VLAN as either tagged or untagged frames." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanCurrentEntry 4 } dot1qVlanCurrentUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports that are transmitting traffic for this VLAN as untagged frames." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanCurrentEntry 5 } dot1qVlanStatus OBJECT-TYPE SYNTAX INTEGER { other(1), permanent(2), dynamicGvrp(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of this entry. other(1) - this entry is currently in use, but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learned dynamically. dynamicGvrp(3) - this entry is currently in use Levi & Harrington Standards Track [Page 64]
RFC 4363 Bridge MIB Extensions January 2006 and will remain so until removed by GVRP. There is no static entry for this VLAN, and it will be removed when the last port leaves the VLAN." ::= { dot1qVlanCurrentEntry 6 } dot1qVlanCreationTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when this VLAN was created." ::= { dot1qVlanCurrentEntry 7 } -- ------------------------------------------------------------- -- The Static VLAN Database -- ------------------------------------------------------------- dot1qVlanStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset." ::= { dot1qVlan 3 } dot1qVlanStaticEntry OBJECT-TYPE SYNTAX Dot1qVlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Static information for a VLAN configured into the device by (local or network) management." INDEX { dot1qVlanIndex } ::= { dot1qVlanStaticTable 1 } Dot1qVlanStaticEntry ::= SEQUENCE { dot1qVlanStaticName SnmpAdminString, dot1qVlanStaticEgressPorts PortList, dot1qVlanForbiddenEgressPorts PortList, dot1qVlanStaticUntaggedPorts PortList, Levi & Harrington Standards Track [Page 65]
RFC 4363 Bridge MIB Extensions January 2006 dot1qVlanStaticRowStatus RowStatus } dot1qVlanStaticName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanStaticEntry 1 } dot1qVlanStaticEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports that are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port, per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed." REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { dot1qVlanStaticEntry 2 } dot1qVlanForbiddenEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports that are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port, per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanStaticEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set." Levi & Harrington Standards Track [Page 66]
RFC 4363 Bridge MIB Extensions January 2006 REFERENCE "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" ::= { dot1qVlanStaticEntry 3 } dot1qVlanStaticUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports that should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set, then it will reject the set operation with an error. For example, a manager might attempt to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanStaticEntry 4 } dot1qVlanStaticRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { dot1qVlanStaticEntry 5 } dot1qNextFreeLocalVlanIndex OBJECT-TYPE SYNTAX Integer32 (0|4096..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The next available value for dot1qVlanIndex of a local VLAN entry in dot1qVlanStaticTable. This will report values >=4096 if a new Local VLAN may be created or else the value 0 if this is not possible. A row creation operation in this table for an entry with a local VlanIndex value may fail if the current value of this object is not used as the index. Even if the value read is used, there is no guarantee that it will still be the valid index when the create operation is attempted; another manager may have already got in during the intervening time interval. In this case, dot1qNextFreeLocalVlanIndex should be re-read Levi & Harrington Standards Track [Page 67]
RFC 4363 Bridge MIB Extensions January 2006 and the creation re-tried with the new value. This value will automatically change when the current value is used to create a new row." ::= { dot1qVlan 4 } -- ------------------------------------------------------------- -- The VLAN Port Configuration Table -- ------------------------------------------------------------- dot1qPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per-port control and status information for VLAN configuration in the device." ::= { dot1qVlan 5 } dot1qPortVlanEntry OBJECT-TYPE SYNTAX Dot1qPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling VLAN configuration for a port on the device. This is indexed by dot1dBasePort." AUGMENTS { dot1dBasePortEntry } ::= { dot1qPortVlanTable 1 } Dot1qPortVlanEntry ::= SEQUENCE { dot1qPvid VlanIndex, dot1qPortAcceptableFrameTypes INTEGER, dot1qPortIngressFiltering TruthValue, dot1qPortGvrpStatus EnabledStatus, dot1qPortGvrpFailedRegistrations Counter32, dot1qPortGvrpLastPduOrigin MacAddress, dot1qPortRestrictedVlanRegistration TruthValue } dot1qPvid OBJECT-TYPE Levi & Harrington Standards Track [Page 68]
RFC 4363 Bridge MIB Extensions January 2006 SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "The PVID, the VLAN-ID assigned to untagged frames or Priority-Tagged frames received on this port. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" DEFVAL { 1 } ::= { dot1qPortVlanEntry 1 } dot1qPortAcceptableFrameTypes OBJECT-TYPE SYNTAX INTEGER { admitAll(1), admitOnlyVlanTagged(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this is admitOnlyVlanTagged(2), the device will discard untagged frames or Priority-Tagged frames received on this port. When admitAll(1), untagged frames or Priority-Tagged frames received on this port will be accepted and assigned to a VID based on the PVID and VID Set for this port. This control does not affect VLAN-independent Bridge Protocol Data Unit (BPDU) frames, such as GVRP and Spanning Tree Protocol (STP). It does affect VLAN- dependent BPDU frames, such as GMRP. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.3" DEFVAL { admitAll } ::= { dot1qPortVlanEntry 2 } dot1qPortIngressFiltering OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When this is true(1), the device will discard incoming frames for VLANs that do not include this Port in its Levi & Harrington Standards Track [Page 69]
RFC 4363 Bridge MIB Extensions January 2006 Member set. When false(2), the port will accept all incoming frames. This control does not affect VLAN-independent BPDU frames, such as GVRP and STP. It does affect VLAN- dependent BPDU frames, such as GMRP. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.4" DEFVAL { false } ::= { dot1qPortVlanEntry 3 } dot1qPortGvrpStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded, and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port. The value of this object MUST be retained across reinitializations of the management system." DEFVAL { enabled } ::= { dot1qPortVlanEntry 4 } dot1qPortGvrpFailedRegistrations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of failed GVRP registrations, for any reason, on this port." ::= { dot1qPortVlanEntry 5 } dot1qPortGvrpLastPduOrigin OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only Levi & Harrington Standards Track [Page 70]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "The Source MAC Address of the last GVRP message received on this port." ::= { dot1qPortVlanEntry 6 } dot1qPortRestrictedVlanRegistration OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The state of Restricted VLAN Registration on this port. If the value of this control is true(1), then creation of a new dynamic VLAN entry is permitted only if there is a Static VLAN Registration Entry for the VLAN concerned, in which the Registrar Administrative Control value for this port is Normal Registration. The value of this object MUST be retained across reinitializations of the management system." REFERENCE "IEEE 802.1u clause 11.2.3.2.3, 12.10.1.7." DEFVAL { false } ::= { dot1qPortVlanEntry 7 } -- ------------------------------------------------------------- -- Per port VLAN Statistics Table -- ------------------------------------------------------------- dot1qPortVlanStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qPortVlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per-port, per-VLAN statistics for traffic received. Separate objects are provided for both the most-significant and least-significant bits of statistics counters for ports that are associated with this transparent bridge. The most-significant bit objects are only required on high-capacity interfaces, as defined in the conformance clauses for these objects. This mechanism is provided as a way to read 64-bit counters for agents that support only SNMPv1. Note that the reporting of most-significant and least- significant counter bits separately runs the risk of missing an overflow of the lower bits in the interval between sampling. The manager must be aware of this possibility, even within the same varbindlist, when interpreting the results of a request or Levi & Harrington Standards Track [Page 71]
RFC 4363 Bridge MIB Extensions January 2006 asynchronous notification." ::= { dot1qVlan 6 } dot1qPortVlanStatisticsEntry OBJECT-TYPE SYNTAX Dot1qPortVlanStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Traffic statistics for a VLAN on an interface." INDEX { dot1dBasePort, dot1qVlanIndex } ::= { dot1qPortVlanStatisticsTable 1 } Dot1qPortVlanStatisticsEntry ::= SEQUENCE { dot1qTpVlanPortInFrames Counter32, dot1qTpVlanPortOutFrames Counter32, dot1qTpVlanPortInDiscards Counter32, dot1qTpVlanPortInOverflowFrames Counter32, dot1qTpVlanPortOutOverflowFrames Counter32, dot1qTpVlanPortInOverflowDiscards Counter32 } dot1qTpVlanPortInFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid frames received by this port from its segment that were classified as belonging to this VLAN. Note that a frame received on this port is counted by this object if and only if it is for a protocol being processed by the local forwarding process for this VLAN. This object includes received bridge management frames classified as belonging to this VLAN (e.g., GMRP, but not GVRP or STP." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3(a)" ::= { dot1qPortVlanStatisticsEntry 1 } dot1qTpVlanPortOutFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only Levi & Harrington Standards Track [Page 72]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "The number of valid frames transmitted by this port to its segment from the local forwarding process for this VLAN. This includes bridge management frames originated by this device that are classified as belonging to this VLAN (e.g., GMRP, but not GVRP or STP)." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3(d)" ::= { dot1qPortVlanStatisticsEntry 2 } dot1qTpVlanPortInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid frames received by this port from its segment that were classified as belonging to this VLAN and that were discarded due to VLAN-related reasons. Specifically, the IEEE 802.1Q counters for Discard Inbound and Discard on Ingress Filtering." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3" ::= { dot1qPortVlanStatisticsEntry 3 } dot1qTpVlanPortInOverflowFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1qTpVlanPortInFrames counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1qPortVlanStatisticsEntry 4 } dot1qTpVlanPortOutOverflowFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1qTpVlanPortOutFrames counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1qPortVlanStatisticsEntry 5 } dot1qTpVlanPortInOverflowDiscards OBJECT-TYPE Levi & Harrington Standards Track [Page 73]
RFC 4363 Bridge MIB Extensions January 2006 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the associated dot1qTpVlanPortInDiscards counter has overflowed." REFERENCE "ISO/IEC 15802-3 Section 14.6.1.1.3" ::= { dot1qPortVlanStatisticsEntry 6 } dot1qPortVlanHCStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qPortVlanHCStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per-port, per-VLAN statistics for traffic on high-capacity interfaces." ::= { dot1qVlan 7 } dot1qPortVlanHCStatisticsEntry OBJECT-TYPE SYNTAX Dot1qPortVlanHCStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Traffic statistics for a VLAN on a high-capacity interface." INDEX { dot1dBasePort, dot1qVlanIndex } ::= { dot1qPortVlanHCStatisticsTable 1 } Dot1qPortVlanHCStatisticsEntry ::= SEQUENCE { dot1qTpVlanPortHCInFrames Counter64, dot1qTpVlanPortHCOutFrames Counter64, dot1qTpVlanPortHCInDiscards Counter64 } dot1qTpVlanPortHCInFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid frames received by this port from its segment that were classified as belonging to this VLAN. Note that a frame received on this port is counted by this object if and only if it is for a Levi & Harrington Standards Track [Page 74]
RFC 4363 Bridge MIB Extensions January 2006 protocol being processed by the local forwarding process for this VLAN. This object includes received bridge management frames classified as belonging to this VLAN (e.g., GMRP, but not GVRP or STP)." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3(a)" ::= { dot1qPortVlanHCStatisticsEntry 1 } dot1qTpVlanPortHCOutFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid frames transmitted by this port to its segment from the local forwarding process for this VLAN. This includes bridge management frames originated by this device that are classified as belonging to this VLAN (e.g., GMRP, but not GVRP or STP)." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3(d)" ::= { dot1qPortVlanHCStatisticsEntry 2 } dot1qTpVlanPortHCInDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of valid frames received by this port from its segment that were classified as belonging to this VLAN and that were discarded due to VLAN-related reasons. Specifically, the IEEE 802.1Q counters for Discard Inbound and Discard on Ingress Filtering." REFERENCE "IEEE 802.1Q/D11 Section 12.6.1.1.3" ::= { dot1qPortVlanHCStatisticsEntry 3 } -- ------------------------------------------------------------- -- The VLAN Learning Constraints Table -- ------------------------------------------------------------- dot1qLearningConstraintsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qLearningConstraintsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing learning constraints for sets of Shared and Independent VLANs." REFERENCE Levi & Harrington Standards Track [Page 75]
RFC 4363 Bridge MIB Extensions January 2006 "IEEE 802.1Q/D11 Section 12.10.3.1" ::= { dot1qVlan 8 } dot1qLearningConstraintsEntry OBJECT-TYPE SYNTAX Dot1qLearningConstraintsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A learning constraint defined for a VLAN." INDEX { dot1qConstraintVlan, dot1qConstraintSet } ::= { dot1qLearningConstraintsTable 1 } Dot1qLearningConstraintsEntry ::= SEQUENCE { dot1qConstraintVlan VlanIndex, dot1qConstraintSet Integer32, dot1qConstraintType INTEGER, dot1qConstraintStatus RowStatus } dot1qConstraintVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the row in dot1qVlanCurrentTable for the VLAN constrained by this entry." ::= { dot1qLearningConstraintsEntry 1 } dot1qConstraintSet OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identity of the constraint set to which dot1qConstraintVlan belongs. These values may be chosen by the management station." ::= { dot1qLearningConstraintsEntry 2 } dot1qConstraintType OBJECT-TYPE SYNTAX INTEGER { independent(1), shared(2) } Levi & Harrington Standards Track [Page 76]
RFC 4363 Bridge MIB Extensions January 2006 MAX-ACCESS read-create STATUS current DESCRIPTION "The type of constraint this entry defines. independent(1) - the VLAN, dot1qConstraintVlan, uses a filtering database independent from all other VLANs in the same set, defined by dot1qConstraintSet. shared(2) - the VLAN, dot1qConstraintVlan, shares the same filtering database as all other VLANs in the same set, defined by dot1qConstraintSet." ::= { dot1qLearningConstraintsEntry 3 } dot1qConstraintStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry." ::= { dot1qLearningConstraintsEntry 4 } dot1qConstraintSetDefault OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The identity of the constraint set to which a VLAN belongs, if there is not an explicit entry for that VLAN in dot1qLearningConstraintsTable. The value of this object MUST be retained across reinitializations of the management system." ::= { dot1qVlan 9 } dot1qConstraintTypeDefault OBJECT-TYPE SYNTAX INTEGER { independent(1), shared(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of constraint set to which a VLAN belongs, if there is not an explicit entry for that VLAN in dot1qLearningConstraintsTable. The types are as defined for dot1qConstraintType. The value of this object MUST be retained across Levi & Harrington Standards Track [Page 77]
RFC 4363 Bridge MIB Extensions January 2006 reinitializations of the management system." ::= { dot1qVlan 10 } -- ------------------------------------------------------------- -- dot1vProtocol subtree -- ------------------------------------------------------------- dot1vProtocolGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1vProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains mappings from Protocol Templates to Protocol Group Identifiers used for Port-and-Protocol-based VLAN Classification." REFERENCE "IEEE 802.1v clause 8.6.4" ::= { dot1vProtocol 1 } dot1vProtocolGroupEntry OBJECT-TYPE SYNTAX Dot1vProtocolGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping from a Protocol Template to a Protocol Group Identifier." INDEX { dot1vProtocolTemplateFrameType, dot1vProtocolTemplateProtocolValue } ::= { dot1vProtocolGroupTable 1 } Dot1vProtocolGroupEntry ::= SEQUENCE { dot1vProtocolTemplateFrameType INTEGER, dot1vProtocolTemplateProtocolValue OCTET STRING, dot1vProtocolGroupId Integer32, dot1vProtocolGroupRowStatus RowStatus } dot1vProtocolTemplateFrameType OBJECT-TYPE SYNTAX INTEGER { ethernet (1), rfc1042 (2), snap8021H (3), snapOther (4), Levi & Harrington Standards Track [Page 78]
RFC 4363 Bridge MIB Extensions January 2006 llcOther (5) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The data-link encapsulation format or the 'detagged_frame_type' in a Protocol Template." REFERENCE "IEEE 802.1v clause 8.6.2" ::= { dot1vProtocolGroupEntry 1 } dot1vProtocolTemplateProtocolValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2 | 5)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identification of the protocol above the data-link layer in a Protocol Template. Depending on the frame type, the octet string will have one of the following values: For 'ethernet', 'rfc1042' and 'snap8021H', this is the 16-bit (2-octet) IEEE 802.3 Type Field. For 'snapOther', this is the 40-bit (5-octet) PID. For 'llcOther', this is the 2-octet IEEE 802.2 Link Service Access Point (LSAP) pair: first octet for Destination Service Access Point (DSAP) and second octet for Source Service Access Point (SSAP)." REFERENCE "IEEE 802.1v clause 8.6.2" ::= { dot1vProtocolGroupEntry 2 } dot1vProtocolGroupId OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Represents a group of protocols that are associated together when assigning a VID to a frame." REFERENCE "IEEE 802.1v clause 8.6.3, 12.10.2.1" ::= { dot1vProtocolGroupEntry 3 } dot1vProtocolGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create Levi & Harrington Standards Track [Page 79]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { dot1vProtocolGroupEntry 4 } dot1vProtocolPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1vProtocolPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains VID sets used for Port-and-Protocol-based VLAN Classification." REFERENCE "IEEE 802.1v clause 8.4.4" ::= { dot1vProtocol 2 } dot1vProtocolPortEntry OBJECT-TYPE SYNTAX Dot1vProtocolPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A VID set for a port." INDEX { dot1dBasePort, dot1vProtocolPortGroupId } ::= { dot1vProtocolPortTable 1 } Dot1vProtocolPortEntry ::= SEQUENCE { dot1vProtocolPortGroupId Integer32, dot1vProtocolPortGroupVid Integer32, dot1vProtocolPortRowStatus RowStatus } dot1vProtocolPortGroupId OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Designates a group of protocols in the Protocol Group Database." REFERENCE "IEEE 802.1v clause 8.6.3, 12.10.1.2" ::= { dot1vProtocolPortEntry 1 } dot1vProtocolPortGroupVid OBJECT-TYPE Levi & Harrington Standards Track [Page 80]
RFC 4363 Bridge MIB Extensions January 2006 SYNTAX Integer32 (1..4094) MAX-ACCESS read-create STATUS current DESCRIPTION "The VID associated with a group of protocols for each port." REFERENCE "IEEE 802.1v clause 8.4.4, 12.10.1.2" ::= { dot1vProtocolPortEntry 2 } dot1vProtocolPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { dot1vProtocolPortEntry 3 } -- ------------------------------------------------------------- -- IEEE 802.1Q MIB - Conformance Information -- ------------------------------------------------------------- qBridgeConformance OBJECT IDENTIFIER ::= { qBridgeMIB 2 } qBridgeGroups OBJECT IDENTIFIER ::= { qBridgeConformance 1 } qBridgeCompliances OBJECT IDENTIFIER ::= { qBridgeConformance 2 } -- ------------------------------------------------------------- -- units of conformance -- ------------------------------------------------------------- qBridgeBaseGroup OBJECT-GROUP OBJECTS { dot1qVlanVersionNumber, dot1qMaxVlanId, dot1qMaxSupportedVlans, dot1qNumVlans, dot1qGvrpStatus } STATUS current DESCRIPTION "A collection of objects providing device-level control and status information for the Virtual LAN bridge services." ::= { qBridgeGroups 1 } qBridgeFdbUnicastGroup OBJECT-GROUP Levi & Harrington Standards Track [Page 81]
RFC 4363 Bridge MIB Extensions January 2006 OBJECTS { dot1qFdbDynamicCount, dot1qTpFdbPort, dot1qTpFdbStatus } STATUS current DESCRIPTION "A collection of objects providing information about all unicast addresses, learned dynamically or statically configured by management, in each Filtering Database." ::= { qBridgeGroups 2 } qBridgeFdbMulticastGroup OBJECT-GROUP OBJECTS { dot1qTpGroupEgressPorts, dot1qTpGroupLearnt } STATUS current DESCRIPTION "A collection of objects providing information about all multicast addresses, learned dynamically or statically configured by management, in each Filtering Database." ::= { qBridgeGroups 3 } qBridgeServiceRequirementsGroup OBJECT-GROUP OBJECTS { dot1qForwardAllPorts, dot1qForwardAllStaticPorts, dot1qForwardAllForbiddenPorts, dot1qForwardUnregisteredPorts, dot1qForwardUnregisteredStaticPorts, dot1qForwardUnregisteredForbiddenPorts } STATUS current DESCRIPTION "A collection of objects providing information about service requirements, learned dynamically or statically configured by management, in each Filtering Database." ::= { qBridgeGroups 4 } qBridgeFdbStaticGroup OBJECT-GROUP OBJECTS { dot1qStaticUnicastAllowedToGoTo, dot1qStaticUnicastStatus, dot1qStaticMulticastStaticEgressPorts, dot1qStaticMulticastForbiddenEgressPorts, dot1qStaticMulticastStatus } Levi & Harrington Standards Track [Page 82]
RFC 4363 Bridge MIB Extensions January 2006 STATUS current DESCRIPTION "A collection of objects providing information about unicast and multicast addresses statically configured by management, in each Filtering Database or VLAN." ::= { qBridgeGroups 5 } qBridgeVlanGroup OBJECT-GROUP OBJECTS { dot1qVlanNumDeletes, dot1qVlanFdbId, dot1qVlanCurrentEgressPorts, dot1qVlanCurrentUntaggedPorts, dot1qVlanStatus, dot1qVlanCreationTime } STATUS current DESCRIPTION "A collection of objects providing information about all VLANs currently configured on this device." ::= { qBridgeGroups 6 } qBridgeVlanStaticGroup OBJECT-GROUP OBJECTS { dot1qVlanStaticName, dot1qVlanStaticEgressPorts, dot1qVlanForbiddenEgressPorts, dot1qVlanStaticUntaggedPorts, dot1qVlanStaticRowStatus, dot1qNextFreeLocalVlanIndex } STATUS current DESCRIPTION "A collection of objects providing information about VLANs statically configured by management." ::= { qBridgeGroups 7 } qBridgePortGroup OBJECT-GROUP OBJECTS { dot1qPvid, dot1qPortAcceptableFrameTypes, dot1qPortIngressFiltering, dot1qPortGvrpStatus, dot1qPortGvrpFailedRegistrations, dot1qPortGvrpLastPduOrigin } STATUS deprecated DESCRIPTION Levi & Harrington Standards Track [Page 83]
RFC 4363 Bridge MIB Extensions January 2006 "A collection of objects providing port-level VLAN control and status information for all ports." ::= { qBridgeGroups 8 } qBridgeVlanStatisticsGroup OBJECT-GROUP OBJECTS { dot1qTpVlanPortInFrames, dot1qTpVlanPortOutFrames, dot1qTpVlanPortInDiscards } STATUS current DESCRIPTION "A collection of objects providing per-port packet statistics for all VLANs currently configured on this device." ::= { qBridgeGroups 9 } qBridgeVlanStatisticsOverflowGroup OBJECT-GROUP OBJECTS { dot1qTpVlanPortInOverflowFrames, dot1qTpVlanPortOutOverflowFrames, dot1qTpVlanPortInOverflowDiscards } STATUS current DESCRIPTION "A collection of objects providing overflow counters for per-port packet statistics for all VLANs currently configured on this device for high-capacity interfaces, defined as those that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." ::= { qBridgeGroups 10 } qBridgeVlanHCStatisticsGroup OBJECT-GROUP OBJECTS { dot1qTpVlanPortHCInFrames, dot1qTpVlanPortHCOutFrames, dot1qTpVlanPortHCInDiscards } STATUS current DESCRIPTION "A collection of objects providing per-port packet statistics for all VLANs currently configured on this device for high-capacity interfaces, defined as those that have the value of the corresponding instance of ifSpeed greater than 650,000,000 bits/second." ::= { qBridgeGroups 11 } qBridgeLearningConstraintsGroup OBJECT-GROUP Levi & Harrington Standards Track [Page 84]
RFC 4363 Bridge MIB Extensions January 2006 OBJECTS { dot1qConstraintType, dot1qConstraintStatus } STATUS current DESCRIPTION "A collection of objects defining the Filtering Database constraints all VLANs have with each other." ::= { qBridgeGroups 12 } qBridgeLearningConstraintDefaultGroup OBJECT-GROUP OBJECTS { dot1qConstraintSetDefault, dot1qConstraintTypeDefault } STATUS current DESCRIPTION "A collection of objects defining the default Filtering Database constraints for VLANs that have no specific constraints defined." ::= { qBridgeGroups 13 } qBridgeClassificationDeviceGroup OBJECT-GROUP OBJECTS { dot1vProtocolGroupId, dot1vProtocolGroupRowStatus } STATUS current DESCRIPTION "VLAN classification information for the bridge." ::= { qBridgeGroups 14 } qBridgeClassificationPortGroup OBJECT-GROUP OBJECTS { dot1vProtocolPortGroupVid, dot1vProtocolPortRowStatus } STATUS current DESCRIPTION "VLAN classification information for individual ports." ::= { qBridgeGroups 15 } qBridgePortGroup2 OBJECT-GROUP OBJECTS { dot1qPvid, dot1qPortAcceptableFrameTypes, dot1qPortIngressFiltering, dot1qPortGvrpStatus, Levi & Harrington Standards Track [Page 85]
RFC 4363 Bridge MIB Extensions January 2006 dot1qPortGvrpFailedRegistrations, dot1qPortGvrpLastPduOrigin, dot1qPortRestrictedVlanRegistration } STATUS current DESCRIPTION "A collection of objects providing port-level VLAN control and status information for all ports." ::= { qBridgeGroups 16 } -- ------------------------------------------------------------- -- compliance statements -- ------------------------------------------------------------- qBridgeCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for device support of Virtual LAN Bridge services. RFC2674 was silent about the expected persistence of the read-write objects in this MIB module. Applications MUST NOT assume that the values of the read-write objects are persistent across reinitializations of the management system and MUST NOT assume that the values are not persistent across reinitializations of the management system." MODULE MANDATORY-GROUPS { qBridgeBaseGroup, qBridgeVlanGroup, qBridgeVlanStaticGroup, qBridgePortGroup } GROUP qBridgeFdbUnicastGroup DESCRIPTION "This group is mandatory for bridges that implement 802.1Q transparent bridging." GROUP qBridgeFdbMulticastGroup DESCRIPTION "This group is mandatory for bridges that implement 802.1Q transparent bridging." GROUP qBridgeServiceRequirementsGroup DESCRIPTION Levi & Harrington Standards Track [Page 86]
RFC 4363 Bridge MIB Extensions January 2006 "This group is mandatory for bridges that implement extended filtering services. All objects must be read-write if extended-filtering services are enabled." GROUP qBridgeFdbStaticGroup DESCRIPTION "This group is optional." GROUP qBridgeVlanStatisticsGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support." GROUP qBridgeVlanStatisticsOverflowGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support. It is most relevant for high-capacity interfaces where the SNMP agent supports only SNMPv1." GROUP qBridgeVlanHCStatisticsGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support. It is most relevant for high-capacity interfaces." GROUP qBridgeLearningConstraintsGroup DESCRIPTION "This group is mandatory for devices implementing both Independent VLAN Learning (IVL) and Shared VLAN Learning (SVL) modes of operation of the filtering database, as defined by IEEE 802.1Q." GROUP qBridgeLearningConstraintDefaultGroup DESCRIPTION "This group is mandatory for devices implementing both Independent VLAN Learning (IVL) and Shared VLAN Learning (SVL) modes of operation of the filtering database, as defined by IEEE 802.1Q." OBJECT dot1qPortAcceptableFrameTypes MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qPortIngressFiltering Levi & Harrington Standards Track [Page 87]
RFC 4363 Bridge MIB Extensions January 2006 MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qConstraintSetDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qConstraintTypeDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." ::= { qBridgeCompliances 1 } qBridgeCompliance2 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for device support of Virtual LAN Bridge services. This document clarifies the persistence requirements for the read-write objects in this MIB module. All implementations claiming compliance to qBridgeCompliance2 MUST retain the values of those read-write objects that specify this requirement." MODULE MANDATORY-GROUPS { qBridgeBaseGroup, qBridgeVlanGroup, qBridgeVlanStaticGroup, qBridgePortGroup2 } GROUP qBridgeFdbUnicastGroup DESCRIPTION "This group is mandatory for bridges that implement 802.1Q transparent bridging." GROUP qBridgeFdbMulticastGroup DESCRIPTION "This group is mandatory for bridges that implement 802.1Q transparent bridging." Levi & Harrington Standards Track [Page 88]
RFC 4363 Bridge MIB Extensions January 2006 GROUP qBridgeServiceRequirementsGroup DESCRIPTION "This group is mandatory for bridges that implement extended filtering services. All objects must be read-write if extended-filtering services are enabled." GROUP qBridgeFdbStaticGroup DESCRIPTION "This group is optional." GROUP qBridgeVlanStatisticsGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support." GROUP qBridgeVlanStatisticsOverflowGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support. It is most relevant for high-capacity interfaces where the SNMP agent supports only SNMPv1." GROUP qBridgeVlanHCStatisticsGroup DESCRIPTION "This group is optional as there may be significant implementation cost associated with its support. It is most relevant for high-capacity interfaces." GROUP qBridgeLearningConstraintsGroup DESCRIPTION "This group is mandatory for devices implementing both Independent VLAN Learning (IVL) and Shared VLAN Learning (SVL) modes of operation of the filtering database, as defined by IEEE 802.1Q." GROUP qBridgeLearningConstraintDefaultGroup DESCRIPTION "This group is mandatory for devices implementing both Independent VLAN Learning (IVL) and Shared VLAN Learning (SVL) modes of operation of the filtering database, as defined by IEEE 802.1Q." GROUP qBridgeClassificationDeviceGroup DESCRIPTION "This group is mandatory ONLY for devices implementing VLAN Classification as specified in IEEE 802.1v." Levi & Harrington Standards Track [Page 89]
RFC 4363 Bridge MIB Extensions January 2006 GROUP qBridgeClassificationPortGroup DESCRIPTION "This group is mandatory ONLY for devices implementing VLAN Classification as specified in IEEE 802.1v." OBJECT dot1qPortAcceptableFrameTypes MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qPortIngressFiltering MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qConstraintSetDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1qConstraintTypeDefault MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1Q." OBJECT dot1vProtocolGroupId MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1v." OBJECT dot1vProtocolGroupRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required as this is an optional capability in IEEE 802.1v." ::= { qBridgeCompliances 2 } END Levi & Harrington Standards Track [Page 90]
RFC 4363 Bridge MIB Extensions January 2006 6. Acknowledgements Much of the groundwork for this document was performed by the IEEE 802.1 working group during the definition of the IEEE 802.1D updates [802.1D] and IEEE 802.1Q [802.1Q]. The authors wish to thank the members of the Bridge Working Group, and David Harrington, Anders SW Christensen, Andrew Smith, Paul Langille, Anil Rijhsinghani, and Keith McCloghrie in particular for their comments and suggestions, which improved this effort. Editing for the final version was done by David Levi. The new textual conventions related to VLAN-IDs were produced as a result of a review of the use of VLAN-ID in several MIB modules. Further investigation found that VLAN-ID objects were defined in a few other MIB modules. The editor would like to thank all who contributed to the discussion that resulted in these new textual conventions. Specifically, Bert Wijnen, Les Bell, Andrew Smith, Mike Heard, Randy Presuhn, Dan Romascanu, Eduardo Cardona, Tom Petch, Juergen Schoenwaelder, Richard Woundy, Tony Jeffree, and William Murwin. We also received input and feedback from IEEE confirming that the values 0 and 4095 are not used for identifying a specific VLAN-ID and so can be used to represent none or a wildcard (see Appendix A). 7. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These tables and objects and their sensitivity/vulnerability are described below. The following tables and objects in the P-BRIDGE-MIB can be manipulated to interfere with the operation of priority classes. This could, for example, be used to force a reinitialization of state machines, thus causing network instability. Another possibility would be for an attacker to override established policy on port priorities, thus giving a user (or an attacker) unauthorized preferential treatment. dot1dTrafficClassesEnabled dot1dGmrpStatus dot1dPortPriorityTable dot1dUserPriorityRegenTable Levi & Harrington Standards Track [Page 91]
RFC 4363 Bridge MIB Extensions January 2006 dot1dTrafficClassTable dot1dPortGarpTable dot1dPortGmrpTable The following tables and objects in the Q-BRIDGE-MIB could be manipulated to interfere with the operation of virtual LANs. This could, for example, be used to force a reinitialization of state machines to cause network instability, or changing the forwarding and filtering policies. dot1qGvrpStatus dot1qForwardAllTable dot1qStaticUnicastTable dot1qStaticMulticastTable dot1qVlanStaticTable dot1qPortVlanTable dot1qLearningConstraintsTable dot1vProtocolGroupTable dot1vProtocolPortTable Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability. The objects dot1dDeviceCapabilities and dot1dPortCapabilitiesTable in the P-BRIDGE-MIB could be used by an attacker to determine which attacks might be useful to attempt against a given device. The following read-only tables and objects in the Q-BRIDGE-MIB could be used by an attacker to determine which attacks might be useful to attempt against a given device, could be used by an attacker to detect whether their attacks are being blocked or filtered, or could be used to understand the logical topology of the network. dot1qMaxVlanID dot1qMaxSupportedVlans dot1qNumVlans dot1qFdbTable dot1qTpFdbTable dot1qTpGroupTable dot1qVlanCurrentTable dot1qPortVlanStatisticsTable Levi & Harrington Standards Track [Page 92]
RFC 4363 Bridge MIB Extensions January 2006 SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 8. Normative References [BRIDGE-MIB] Norseth, K. and E. Bell, "Definitions of Managed Objects for Bridges", RFC 4188, September 2005. [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC2674] Bell, E., Smith, A., Langille, P., Rijhsinghani, A., and K. McCloghrie, "Definitions of Managed Objects for Bridges with Traffic Classes, Multicast Filtering and Virtual LAN Extensions", RFC 2674, August 1999. [RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002. Levi & Harrington Standards Track [Page 93]
RFC 4363 Bridge MIB Extensions January 2006 [802.1D] "Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Common specifications - Part 3: Media Access Control (MAC) Bridges: Revision. This is a revision of ISO/IEC 10038: 1993, 802.1j-1992 and 802.6k-1992. It incorporates P802.11c, P802.1p and P802.12e." ISO/IEC 15802-3: 1998. [802.1Q] ANSI/IEEE Standard 802.1Q, "IEEE Standards for Local and Metropolitan Area Networks: Virtual Bridged Local Area Networks", 2003. [802.1t] IEEE 802.1t-2001, "(Amendment to IEEE Standard 802.1D) IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Common specifications - Part 3: Media Access Control (MAC) Bridges: Technical and Editorial Corrections". [802.1u] IEEE 802.1u-2001, "(Amendment to IEEE Standard 802.1Q) IEEE Standard for Local and metropolitan area networks - Virtual Bridged Local Area Networks - Amendment 1: Technical and Editorial Corrections". [802.1v] IEEE 802.1v-2001, "(Amendment to IEEE Standard 802.1Q) IEEE Standards for Local and Metropolitan Area Networks: Virtual Bridged Local Area Networks--Amendment 2: VLAN Classification by Protocol and Port". 9. Informative References [RFC1493] Decker, E., Langille, P., Rijsinghani, A. and K. McCloghrie, "Definitions of Managed Objects for Bridges", RFC 1493, July 1993. [RFC4323] Patrick, M. and W. Murwin, "Data Over Cable System Interface Specification Quality of Service Management Information Base (DOCSIS-QOS MIB)", RFC 4323, January 2006. [RFC4149] Kalbfleisch, C., Cole, R., and D. Romascanu, "Definition of Managed Objects for Synthetic Sources for Performance Monitoring Algorithms", RFC 4149, August 2005. [RFC2613] Waterman, R., Lahaye, B., Romascanu, D., and S. Waldbusser, "Remote Network Monitoring MIB Extensions for Switched Networks Version 1.0", RFC 2613, June 1999. Levi & Harrington Standards Track [Page 94]
RFC 4363 Bridge MIB Extensions January 2006 [RFC3318] Sahita, R., Hahn, S., Chan, K., and K. McCloghrie, "Framework Policy Information Base", RFC 3318, March 2003. [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. Levi & Harrington Standards Track [Page 95]
RFC 4363 Bridge MIB Extensions January 2006 Appendix A. Email from Tony Jeffrey from IEEE -----Original Message----- From: Tony Jeffree [mailto:tony@jeffree.co.uk] Sent: Friday, 6th of June 2003 17:16 To: Wijnen, Bert (Bert) [mailto:bwijnen@lucent.com] Subject: RE: VLAn ID Bert et al - We have concluded that the use of 4095 as a wildcard is acceptable to 802.1, and we will make any necessary changes to 802.1Q in due course to relax the current stated restriction. However, we need to know whether that is all that needs to be done to 802.1Q - i.e., is there any need to change our definitions of the managed objects in the document (Clause 12) to reflect the interpretation of 4095 as a wildcard, or is this simply an issue for the SNMP machinery to handle? Regards, Tony Levi & Harrington Standards Track [Page 96]
RFC 4363 Bridge MIB Extensions January 2006 Authors' Adresses David Levi Nortel Networks 4655 Great America Parkway Santa Clara, CA 95054 USA Phone: +1 865 686 0432 EMail: dlevi@nortel.com David Harrington Effective Software 50 Harding Rd. Portsmouth, NH 03801 USA Phone: +1 603 436 8634 EMail: ietfdbh@comcast.net Vivian Ngai Salt lake City, UT USA EMail: vivian_ngai@acm.org Les Bell Hemel Hempstead Herts. HP2 7YU UK EMail: elbell@ntlworld.com Andrew Smith Beijing Harbour Networks Jiuling Building 21 North Xisanhuan Ave. Beijing, 100089 PRC Fax: +1 415 345 1827 EMail: ah_smith@acm.org Levi & Harrington Standards Track [Page 97]
RFC 4363 Bridge MIB Extensions January 2006 Paul Langille Newbridge Networks 5 Corporate Drive Andover, MA 01810 USA Phone: +1 978 691 4665 EMail: langille@newbridge.com Anil Rijhsinghani Accton Technology Corporation 5 Mount Royal Ave Marlboro, MA 01752 USA EMail: anil@accton.com Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Phone: +1 408 526 5260 EMail: kzm@cisco.com Levi & Harrington Standards Track [Page 98]
RFC 4363 Bridge MIB Extensions January 2006 Full Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgement Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Levi & Harrington Standards Track [Page 99]

   

[Home] [Full RFC index] [RFC humour] [Our technology]

Copyright © Inter-Corporate Computer & Network Services, Inc.  All rights reserved.
All trademarks and RFC contents are the property of their respective owners.